£61.20 exc vat
£73.44 inc vat
In stock
£61.20 exc vat
£73.44 inc vat
In stockRecommended usage 1 x R33636-20 to fit one mini.
3 OF 0.625 COMPRESSION RINGS AND .1575 OIL CONTROL RING.AT PLUS 20 OVERSIZE FOR P20773 pistons
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
Low drag 1275 piston standard size 2.780 plus 20 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.7...
998cc dished circlip type piston with 4 rings. Compression range of 8.3 to 9:1 depending on block and head but for best performance use later 3 ring flat top piston ADU3490-20. Sold singly,4 per engine required
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...
These are suitable for press fit gudgeon pin late type 998 con rods.
sold individually with rings and pin complete
Ringsets are available as R43240-20
Crankshaft washers for crankshaft at 3 thou oversize on each one
sold as a set of four for 998 and 1100cc.
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Main bearings plus 60 oversize, 1275 2" mains. 60 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
Sintered copp...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
WASHER FOR THE OIL PRIMING HOLE PLUG WHEN APPLICABLE 850/997/998 and also on earlier type oil pressure switch or oil pressure union CAM6431.
Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S
( Tri-Metal )
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin ...
Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead...
Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.