(¥130) £130.14 exc vat
(¥156) £156.17 inc vat
In stock
Has 7 V shape or 14 fins/gills. C-ARA4442 (2 core) has 12 per inch.
This has 3 large oval shape in line tubes whereas the standard ARP2000 has 3 offset tubes.
More espensive to produce than the 2 core but slightly better overall with same top tank as all our special radiators. On the road seems equal to our 2 core type but seems to have a better heat dispensation when engine is turned off, or idling by not boiling over, or loosing water and holding pressue when used with 15lb rad cap.
The fins allow more air through when stationary.
As used by Peter Baldwin the Mini Miglia champion and other Historic drivers.
Not suitable for grasstrack or Autocross as any heavy deluge of mud or muck could block or damage the large V shaped fins in the core.
The 2 piece radiator cowling fitted to Cooper and S is avaialbe as ARA2770 and this rad fits Mk1/2 engine bay perfectly.
If your engine still overheats check the water pump for cavitation as caused on non genuine pumps and always fit an electric fan if engine is well tuned.
If you have the radiator out it makes sence to change to an evolution type lightweight water pump GWP187[/link with 3 year warranty and new fan belt of course. If you have a by pass hose see [link]GWP134
(¥130) £130.14 exc vat
(¥156) £156.17 inc vat
In stockRecommended usage 1 x ARP1106 to fit one mini.
m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)
original imperial radiator screws were SH604031 or PK type were ARA1117
Minispares own UK manufactured product with original shape mini header tank, now with drain plug in lower tank which doubles up to also accept the screw in type sensor for later cars. It has about 20 fins/ gills per inch with 2 tubes in the core and ...
Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engines which used the longest hose....
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
The heater is not available anymore, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air.
This fits the early Mk1 cars only with 5" gap between pipe hole centres, after 1963 17H8608
m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)
original imperial radiator screws were SH604031 or PK type were ARA1117
Universal aluminium heater assembly complete with heater matrix and electric fan. Comes with 2 outlets for demisting windscreen and 2 variable vents for heating the rest of the car. Ideal for track/race cars or simply for those who want to replace th...
Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Designed to reduce the horsepower drain and slow down the water moving through the radiator to allow it time to cool, its very important for the higher RPMs we run today. This oversize pulley is 4.2" diameter, earlier cars used a 3.875" wide pulley. ...
Replacement electric fan assembly complete with laser cut metal brackets so that it can be mounted to the original mounting points of the standard fan
uses 9" blowing air fan.
Radiator hose kit for all mpi Minis. This kit has top and bottom radiator hoses all in shiney blue Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer who never wants a failure or th...
Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney black Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer ...
Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney blue Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer w...
Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever! Made to fit 1275cc cylinder head the length is made to cover 1275cc engines includi...
Red Silicon Top Radiator Hose
Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever!Made to fit any 850/998/1100cc minis plus HI...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.