(¥209) £208.86 exc vat
(¥251) £250.63 inc vat
Special order
(¥209) £208.86 exc vat
(¥251) £250.63 inc vat
Special orderRecommended usage 1 x CK960H to fit one mini.
Make it like a Rolls Royce! The Mini will never be as quiet as a Rolls but every bit helps. If you have a carpet kit without this insulation you are missing a great opportunity for increased comfort. The kit includes a tailored floor set,front wheel ...
Our lightweight underfelt kit is the perfect companion when fitting a new headlining. Made from lightweight felt and cut to size, this fits into the cavity of the roof before fitting your new headlining and provides increased sound insulation and pro...
Static 3 point fixing front seatbelt with the female fixing on a stem.
These panels hold the door panels in place under tension inside the door aperture. It is not essential, but well worth replacing or renewing these in conjunction with new door panels. Sold in pairs.
Black door pocket liner for the R/H door which has sliding windows and external hinges
Black door pocket liner for the L/H door which has sliding windows and external hinges
13 piece black trim kit as fitted to MK3 Cooper "S" and Mini from 1970 to-may 1973 when the rear quarter panel trim shape changed deleting ash tray mount
This 13 piece kit is available in factory colours and to the exact design pattern as or...
Fitted 1969-77 and 1992-96 originally and white from 1970-96 so see PAM5401BLACK and PAM5401AP. C posts trims changed with MPI or Heritage shells.
These headlinings are held in by different shape/length rods which a...
Reproduction gear lever gaiter for all remote control type gearboxes with the short gear lever by the driver's seat. The metal retainer for this gaiter is 14A9942. These were fitted until the introduction of the rod change type [link]CZH...
Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5
Also used for 24A1169 glove box moulding MK1/2.
Seal for door handles MK1/2 and all sliding window exterior hinge cars.
also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate
is oval shaped
for boot / rear door use the hole at the rear ...
Fire retardent felt with correct cut outs for MK3 cars for the mini firewall just behind the carb and air cleaner full width of the panel see FELT860 for spray adhesive.
The black vinyl covering that lays on your lower dash shelf. For cars after 1970 where the facia panel is not a full metal panel you must fit (link)DT3076(/link)
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI to Mk3 Minis pre 1976 and on the accellerator pedal from 1976 -1996.
The lower brightwork moulding for finishing off the lower dash, crash pad rail or on earlier cars the painted metal surface of the panel which holds the switch panel section.See 14A8010 for clip
This moulding was fitted to all m...
Fitted for safety regulations to all MK2 minis from 1967-80 except Sweden and Canada to 1975 (not any MKI or van and pick up). Later commercial type minis did have it fitted with 3 clock speedo pod. This is a hard foam pad at the lower edge of the pa...
Dash liners without air vents for either side of the speedo on deluxe versions such as the Cooper S with centre speedo and two gauges which are black vinyl covered as opposed to the painted type. Not for the single centre clock only.
see [li...
Rocker light switch with blade connectors on the back. FITS MK3.
This universal trim clip with smaller D shape and exta short claws section is for rear seat and for headlings. For MK1/2 minis and Traveller/Estate versions there are 25 and MK3 on there are 13.
For the clip with a larger D and claw spike se...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.