(¥83) £82.50 exc vat
(¥99) £99.00 inc vat
In stock
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This camshaft does not really need 1.5 rockers as the lifts are good.
If you have 1.5 rockers see optionEVOLUTION002.
Mini Spares and many leading engine tuners in USA have used this camshaft in their engines for over 15 years-and found nothing better-it is fitted to our half engines ENG001/002/003 because of its great useful torque range and economy. Good for all 1275-1380 and over 300 sold every year its that brilliant.
Also very low on carbon emmissions for that all important MOT. Ok in 998cc upwards but depending on tune might have slightly lumpy, erratic tickover.
See Miniworld November edition 2014 page 60 where Simon at Mini Spares done a camshaft swap thinking this was close to an old AEG510 but modern design. This it was not but he was delighted with the extra performance and smoothness. Both Noah 1293cc with 102bhp and Justin at Mini Spares 1380 with 127bhp have these cams in their minis.
SEAT DURATION ON INLET 257 AND EX 252
CAM LIFT IN 264 EX 289
VALVE LIFT IN 327 EX 358 STD
VALVE LIFT IN 393 EX 430 1.5 LIFT
Should be timed in at 107 degrees as optimum, NO NEED FOR HI LIFT ROCKERS
Manufactured from new blanks, so sold as an outright sale no exchange required.
Cam lube should be used on all new camshafts
(¥83) £82.50 exc vat
(¥99) £99.00 inc vat
In stockRecommended usage 1 x EVOLUTION001 to fit one mini.
The ultimate cam follower with oil hole, designed to minimise float and jump normally seen in original cam followers, which ultimately loses power. Precision ground outside diameter with smaller chamfered base to give more surface area for extra hi l...
Modern high lift, short duration camshafts have posed quite a few problems for the general public in recent years. Widely available performance valve springs were outdated overnight, as it became necessary to reduce spring crush. This, in turn, cause...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
A vital aid for accurately timinig non-factory camshafts. This disc is a 360 degree protractor disc made by kent cams.
Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
A Plus Electronic Ignition distributor with vac unit, modified to our spec in UK to give best performance on any minis with std to 276 camshaft profile.
Ideal for our EVOLUTION001 camshaft
Brand New distributor complet...
Hottest road usable cam. Not a good traffic cam. Lumpy idle. Not very suitable for small bore units unless fully prepared with big valve head. Very strong mid and top end power. Rev range 2,000 - 7,500 rpm.
See EVOLUTION001...
Genuine Mini Spares camshaft for use with 1.5 rockers if preferred--below 5000rpm should produce more power than the 286 profile. Close to MDM274
Cam Timing
107 degrees at full lift on No1 inlet
SEAT...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Genuine Mini Spares camshaft for use with 1.5 rockers if preferred--below 5000rpm should produce more power than the 286 profile. Close to MDM274
Cam Timing
107 degrees at full lift on No1 inlet
SEAT...
The only upgrade in camshaft you can get away with on the multi point injection cars without changing ECU etc--A mild road cam.
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and we will only supply camshafts fro...
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
"Scatter Pattern" cams were designed by David Vizard to work best with the pecularities of the A-Series' siamese intake ports. The 310 scatter pattern is the ultimate race cam. Needs fully prepared engine for good results - high CR, high flow head, ...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Brilliant all round performance road cam. Smooth idle, pulls from around 1,200 RPM. Small gain in low end, big increase in med and top end. Unbeatable for genuine fast road use. Rev band 1,200 to 6,500/7,000 rpm. Intake duration is 260 degrees, exh...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter
General: Camshaft Drive Systems
For highly tuned engines always use steel duplex as cast is nowhere as st...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
MD266 in A plus form with cam followers.valve springs and initial set up oil.
For timing disc, order separately as C-AJP337
As of July 2007 Kent cams have no supply of old camshafts for reprofiling a...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.