(¥1,148) £1.147.79 exc vat
(¥1,377) £1.377.35 inc vat
(¥1,148) £1.147.79 exc vat
(¥1,377) £1.377.35 inc vat
Recommended usage 1 x FZX3052A to fit one mini.
Cast alloy type,this intake manifold for twin 1.25"SUs (H2 or H4 -- NOT HS4)
It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places. Further blending ...
The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.
Accelerator bracket for twin carb models, mounts to inlet manifold.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...
This is the left hand linkage lever that sits on the rods between HS type twin carbs.sold individually
Stainless steel twin HS2 heatshields kit. Comes with link bar, bolts, nuts and springs.
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Special clip for all our braided s/steel petrol hoses.14mm to 16mm.
This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
A special 3/8" unf half nut (9/16"AF spanner size)for fitting on rear brake hoses and carbs to manifold.
Bolt used in our anti roll bar kit and for holding plate on speedo drive housing on gearbox
This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
Our heavy duty throttle cable is superior in many ways.
A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.
Cable to carb bolt is ACC5062.
Correct and original thickness oil for SU carb dashpots.
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...
The proper slot head screw for the SU dashpot and float lid 3/16 whitworth thread.
Accelerator bracket for twin carb models, mounts to inlet manifold.
The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.