($200.00) £200.00 exc vat
($240.00) £240.00 inc vat
In stock
The double skin Mk1/2 type 8G9270 introduced in december 1966 is only available as non Genuine item, see 8G9270MS
Fit 14A9838 Boot board for protection.
Need new cables for the boot lid? See 14A6740.
An outer skin is only available im aluminium, see HMP441051
($200.00) £200.00 exc vat
($240.00) £240.00 inc vat
In stockRecommended usage 1 x 28G110 to fit one mini.
Up until December 2003 we would have been embarrased to sell the only chrome
boot hinges available. They were bad fitting, looked poor quality and had so much play in them they were totally useless. But along came a set which does fit and is...
This liner was found on many deluxe Minis. The black fiberboard is held on by chrome screws and upholstery washers. Put it on any year Mini.
The original T shape boot handle as fitted to the bootlid of MK1/2 plus vans and estates except the wooden variety....
uses the ADA3817 type of seal, hole will need cutting to suit the shaft of the handle
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Non genuine single skin MKI boot lid. Always fix your swinging number plate and hinges on for dummy fit and alignment before spraying.
If you have any doubt about the value of these panels- try having the rust and dents removed fr...
MkI aluminium boot lid "skin only" panel. This panel is produced off the original tooling, ensuring good panel fit and integrity. Following the pressing of the panel it is hand finished by Heritage craftsmen, to ensure the highest panel quality.
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Very light, rustproof fiberglass boot lid SKIN. MKI replica with numberplate recess.
The boot floor (trunk of the Mini) has always been an area with a great potential to rust. Not only is it often exposed to battery acid but typically water collects there and rust results. BM Heritage produce a sub assembly from original tooling tha...
Genuine metal battery box. always going rusty owing to the location of where they are fitted. Requires welding in place and preferably painted or protective coat of some kind and remember to check if the battery cover, strap and clips need changing...
The genuine bootlid fitted from 1988 where the seal sits on the car body rather than the bootlid itself. The only difference between this and the earlier BMP339 is that it does not have holes drilled for the boot seal clips.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
If you want to hold it in place then this is easy and simple. 4" long rubber hooks can be used on bonnet and/or boot lid. Packaged in pairs with both brackets.
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
These chrome spring type clips are used to keep the bonnet and boot from coming open on competition cars and are available in black. Holes will be required in the fitting of these so if you do not want to drill your body panels these are not for you....
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.