DISTRIBUTOR 65D 90-93 HIF44 CARB COOPER
AUU1536

($80.50) £80.50 exc vat

($96.60) £96.60 inc vat

In stockIn stock
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.

Replacement service items for this are:

Cap GDC156

Rotor arm GRA2143

Should be used with GCL143 coil.

($80.50) £80.50 exc vat

($96.60) £96.60 inc vat

In stockIn stock

Recommended usage 1 x AUU1536 to fit one mini.
Distributors - Qty 1

Kit products
SPI TO HIF44 CARB CONVERSION KIT
C-STN23

To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.

($1,424.57) £1.424.57 exc vat

($1,709.48) £1.709.48 inc vat
People also bought products
DISTRIBUTOR ELECTRIC EVOLUTION FOR 285-296 CAMS
C-27H7699

Pre A plus Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles

Brand New distributor complete with electronic conversion already fitted.

PRE A PLUS
<...

($82.50) £82.50 exc vat

($99.00) £99.00 inc vat
DISTRIBUTOR 25D WITH VAC ELECTRONIC - NEG EARTH
GEU930MS

NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...

($72.00) £72.00 exc vat

($86.40) £86.40 inc vat
DISTRIBUTOR 45D ELECTRONIC pre A PLUS NEG EARTH ON...
BAU1962MS

NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .

replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...

($67.50) £67.50 exc vat

($81.00) £81.00 inc vat
SCREW KIT FOR 45D / 59D DISTRIBUTORS
57H5135

These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106

($1.80) £1.80 exc vat

($2.16) £2.16 inc vat
DISTRIBUTOR CAP RETAINING CLIP FOR 45D DIZZY'S
GDC136CLIP

Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.

($2.50) £2.50 exc vat

($3.00) £3.00 inc vat
BRACKET FOR DIZZY SHIELD TO BLOCK (BOTTOM OF SHIEL...
JZV1073

Bracket for attaching the Distributor water shield block to gearbox stud/bolt

Does not come with fixing clips, these are available seperately as part number 13H6461

Upper bracket-NJU10002

Lower bracket- JZV1073

The...

($3.50) £3.50 exc vat

($4.20) £4.20 inc vat
IGNITION MODULE FOR ELECTRONIC DISTRIBUTOR
NJC10001

Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.

($30.00) £30.00 exc vat

($36.00) £36.00 inc vat
ROTOR ARM FOR 25D TYPE PERFORMANCE TYPE
GRA101

If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...

($12.00) £12.00 exc vat

($14.40) £14.40 inc vat
DISTRIBUTOR 123 ELECTRONIC IGNITION WITH VAC A+
C-27H7773

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 pre programmed advanced curves built in, a must for any mini with a worn distributor. Full instructions are included with the system. For any A series, A Plus engines...

($277.50) £277.50 exc vat

($333.00) £333.00 inc vat
LUMENITION FOR 23/25D DIST
MTK003

See MTK007 for details. Suitable for negative earth only. For positive earth use LU142AP12

also see our negative earth distributors with built in electronics GEU930MS

or 12G2140MS

($112.50) £112.50 exc vat

($135.00) £135.00 inc vat
CONTACT POINTS MINI+METRO POST 80 DUCELLIER DISTR...
GCS119

fitted to ducellier distributors only which are recognised by their red cap.

($4.50) £4.50 exc vat

($5.40) £5.40 inc vat
DISTRIBUTOR SPINDLE O RING SEAL
513682A

The O ring that actually sits on the distributor drive spindle shaft in the recess provided.

($0.48) £0.48 exc vat

($0.58) £0.58 inc vat
VACUUM PIPE ELBOW
12B2062

The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...

($2.25) £2.25 exc vat

($2.70) £2.70 inc vat
DISTRIBUTOR RETAINING CLAMP.A PLUS pre 85
613857A

prong type clamp that bolts to the block and retain the A plus distributor in place--use TAM1671 the bolt is TAM1706

($4.71) £4.71 exc vat

($5.65) £5.65 inc vat
DISTRIBUTOR CAP FOR 25D DISTRIBUTOR TOP ENTRY
GDC103

Top-entry cap takes plug-in wires and will interchange with GDC102. This is an alternative for side entry cap GDC102 which some believe is less prone to wet-weather problems. Features aluminium contacts.

($4.80) £4.80 exc vat

($5.76) £5.76 inc vat
DIST CLAMP PRE A PLUS
501134

This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.

($10.70) £10.70 exc vat

($12.84) £12.84 inc vat
DISTRIBUTOR ORIGINAL MINI 25D TYPE WITH VAC UNIT
GEU930

Range of distributors with modern day curves built,programmed and tested for Mini Spares in UK.

Beware of cheap China made units that are poorly made- see note at bottom. GEU930 25D 850/early 998

12G2140 ...

($43.83) £43.83 exc vat

($52.60) £52.60 inc vat
CONNECTOR FOR ADVANCE RETARD VACUUM PIPE
12B2095

Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...

($0.90) £0.90 exc vat

($1.08) £1.08 inc vat
DISTRIBUTOR SHIELD COVER FOR ELECTRICS LATEST TYPE
BHM1675

The current genuine large plastic shield with all fittings required to cover the engine electrics.

Parts are available seperately:

The plastic clips are 13H6461.

Upper bracket is NJU10002 x 2 requ...

($29.79) £29.79 exc vat

($35.75) £35.75 inc vat
DISTRIBUTOR CLAMP FOR A PLUS DIZZY 85 ON
TAM1671

Prong type clamp that bolts to the block and retains the A plus distributor in place. The screw is TAM1706.

Pre A plus clamp is 501134

($6.00) £6.00 exc vat

($7.20) £7.20 inc vat