BOOTLID 1988 TO 2000 (uses CKE10018 LATE TYPE SEAL...
BMD36001

($260.00) £260.00 exc vat

($312.00) £312.00 inc vat

In stockIn stock
The genuine bootlid fitted from 1988 where the seal sits on the car body rather than the bootlid itself. The only difference between this and the earlier BMP339 is that it does not have holes drilled for the boot seal clips.

($260.00) £260.00 exc vat

($312.00) £312.00 inc vat

In stockIn stock

Recommended usage 1 x BMD36001 to fit one mini.
Bootlid - Qty 1

Recommended products

These screws fit the lower 2 holes on all boot hinges.Also see 24A2175/6 gaskets

that you will need. 1/4" unf 5/8"long, also for tailgate stays on pickup.

These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.

These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.

This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.

Alternative products
People also bought products

Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.

Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.

MKI boot lid manufactured by British Motor Heritage. Always fix your swinging number plate and hinges on for dummy fit and alignment before spraying.

The double skin Mk1/2 type 8G9270 introduced in december 1966 is only availabl...

Non Genuine metal battery box. always going rusty owing to the location of where it is fitted. Requires welding in place and preferably painted or a protective coat. Remember to check if the battery cover, strap and clips need changing. Popular afte...

The boot floor (trunk of the Mini) has always been an area with a great potential to rust. Not only is it often exposed to battery acid but typically water collects there and rust results. BM Heritage produce a sub assembly from original tooling tha...

Non genuine mini boot lid with full skin inner frame. The genuine alternative to this is BMP339 with an open back.

This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.

The boot board bracket 14A9783 is not included

For 10" wheels with 145 tyres ...

This kit contains all the brackets and mounts required for fitting Minis with 10/12" wheels or with 145 profile tyres.

The boot board bracket 14A9783 is not included

For 10" wheels with 145 tyres and 5.5 gallon tank se...

This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.

3.3mm thick from the tanneries for use on horse bridles,wit...

Full carpet boot liner kit, completely lines the inside of the boot area.



Not suitable for MPI minis.

Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.

Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)

A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).

Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...

This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.

This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.

This kit does not include the bracket on the boot board 14A9783