GRANT REPLACEMENT PISTON RING SET 998 A+ +20

3 OF 0.625 COMPRESSION RINGS AND .1575 OIL CONTROL RING.AT PLUS 20 OVERSIZE FOR P20773 pistons

($45.00) £45.00 exc vat

($54.00) £54.00 inc vat

SINGLE PISTON RING SET FOR R33636-20

08-522407-00

($16.32) £16.32 exc vat

($19.58) £19.58 inc vat

PISTON SET 998 HC CIRCLIP TYPE +20 OVERSIZE

ADU3490-20

998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...

($152.00) £152.00 exc vat

($182.40) £182.40 inc vat

1275 +20 HIGH COMPRESSION PISTON - SINGLE

P21253-20

Low drag 1275 piston standard size 2.780 plus 20 thou oversize(Rings included).

This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.

The best performance 1275 pistons are C-STN100 range which have 9.7...

($73.50) £73.50 exc vat

($88.20) £88.20 inc vat

PISTON SINGLE MINI 998cc +020

P20773-20

998cc dished circlip type piston with 4 rings. Compression range of 8.3 to 9:1 depending on block and head but for best performance use later 3 ring flat top piston ADU3490-20. Sold singly,4 per engine required

($70.59) £70.59 exc vat

($84.71) £84.71 inc vat

PISTON SINGLE 1098cc MINI +0.040

P20397-40

This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...

($52.26) £52.26 exc vat

($62.71) £62.71 inc vat

PISTON RING SET FOR 998 A PLUS STD

R33636-00

3 OF 0.625 COMPRESSION RINGS AND .1575 OIL CONTROL RING.

($63.30) £63.30 exc vat

($75.96) £75.96 inc vat

PISTON. SINGLE 998 FLAT TOP LATE TYPE 10.3 TO 1 /

P22463-20

These are suitable for press fit gudgeon pin late type 998 con rods.

sold individually with rings and pin complete

Ringsets are available as R43240-20

($37.50) £37.50 exc vat

($45.00) £45.00 inc vat

CRANK THRUST WASHER SET 998 3 THOU OVERSIZE

ACL2122-003

Crankshaft washers for crankshaft at 3 thou oversize on each one

sold as a set of four for 998 and 1100cc.

($17.25) £17.25 exc vat

($20.70) £20.70 inc vat

ACL SMALL BORE ENGINE CAM LINER SET

ACL3046

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

($16.14) £16.14 exc vat

($19.37) £19.37 inc vat

MINI 1275 CAM LINER SET

MS3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

($15.75) £15.75 exc vat

($18.90) £18.90 inc vat

MAINS SET 60 OVERSIZE PRE A PLUS/EARLY A+ 1275

AEM91120-60

Main bearings plus 60 oversize, 1275 2" mains. 60 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

Sintered copp...

($26.25) £26.25 exc vat

($31.50) £31.50 inc vat

CRANK THRUST WASHER SET +0.30" 1275

ACL2136-030

Set of +0.030" size 1275 crank thrust washers.

($11.25) £11.25 exc vat

($13.50) £13.50 inc vat

CRANK THRUST WASHER SET +0.003" 1275

ACL2136-003

Set of +0.003" size 1275 crank thrust washers.

($11.25) £11.25 exc vat

($13.50) £13.50 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat

TIMING CHAIN SINGLE ROW SPECIAL QUALITY

3H2127EVO

Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.

This chain saves all the time and effort requ...

($22.05) £22.05 exc vat

($26.46) £26.46 inc vat

1° OFFSET WOODRUFF KEY

WKN1OSET

Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...

($10.50) £10.50 exc vat

($12.60) £12.60 inc vat

WASHER FOR ENGINE OIL PRIMING PLUG

6K464

WASHER FOR THE OIL PRIMING HOLE PLUG WHEN APPLICABLE 850/997/998 and also on earlier type oil pressure switch or oil pressure union CAM6431.

($0.60) £0.60 exc vat

($0.72) £0.72 inc vat

ENGINE TO GEARBOX NUT AND BOLT KIT

MSSK060

Complete nut, bolt and washer set for engine to gearbox only

($3.50) £3.50 exc vat

($4.20) £4.20 inc vat

BIG ENDS PLUS 30 OVERSIZE 1275 EXCEPT COOPER S

AEB91306-30

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

($30.00) £30.00 exc vat

($36.00) £36.00 inc vat

BIG ENDS PLUS 40 OVERSIZE 998/1100 COOPER S

AEB572-40

Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

( Tri-Metal )

Sintered copper lead...

($28.02) £28.02 exc vat

($33.62) £33.62 inc vat

BIG ENDS PLUS 30 OVERSIZE 998/1100 COOPER S

AEB572-30

Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

( Tri-Metal )

Sintered copper lead...

($22.96) £22.96 exc vat

($27.55) £27.55 inc vat