£67.50 exc vat
£81.00 inc vat
In stock
list below for other markings
17 teeth central groove
18 teeth offset groove to one edge
19 teeth 3 groove markss
£67.50 exc vat
£81.00 inc vat
In stockRecommended usage 1 x DAM2808 to fit one mini.
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
This gearbox is identical to MSG05 except for a 3.2 final drive which effectively gives you a final drive ratio of 2.82 in 5th.
Do not come with input gear supplied.
Surcgharge on old unit £400+ VAT
This gearbox is identical to MSG04 except for a 3.2 final drive which effectively gives you a final drive ratio of 2.822 in 5th.
Does not come with input gear supplied.
New for 2023, special heavy duty 2nd and 3rd gears with laygear and 1st motion to match giving a quiet road box suitable for engines producing upto 125lbft of torque on naturally aspirated engines.
Ratios are:
1s...
New for 2023, special heavy duty 2nd and 3rd gears with laygear and 1st motion to match giving a quiet road box suitable for engines producing upto 125lbft of torque on naturally aspirated engines.
Ratios are:
1s...
New for 2023, special heavy duty 2nd and 3rd gears with laygear and 1st motion to match giving a quiet road box suitable for engines producing upto 125lbft of torque on naturally aspirated engines.
Ratios are:
1s...
59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.
The 17 tooth pinion on the gearbox mainshaft to drive the 3.65 1100 (ADO16 cars) and 3.76 early mini crownwheels.
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
A bronze type bush that fits in the gearbox output shaft side cover on early automatics and Cooper S with hardy spicer type joints. These are larger than the standard mini or rod change engine gearbox types which take 2A3538.
The gearbox diff side plate bonze colour bush for all except auto and cooper S with hardy spicer output shafts. Sold singly 2 required per gearbox.
clearance needs to be 0.03mm
See DAM3108 also for smaller diff shims. Refer to workshop manual for fitment.
The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...
Bolt for holding the Clutch End cover (Wok) onto the flywheel housing.
Also for the CHM85 differential side cover 1" long unc 5/16" bolt.
A plus type bolt with built in washer on head, known as flanged head bolt.
Standard replacement precision ground upgraded material standard diff pin. Recommended for all standard differential rebuilds. For performance, use C-BTA164 moly coated pin with standard planet gears. Pay special attention to the conditi...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details
Quantity required is 2 per gearbox but the idler gear requires shimming for correct...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.