During a recent discussion with a few overseas Mini brethren - who were experiencing various engine-related problems - something cropped up that I have always taken as granted (in the sense of ' a standard for the application'); the matter of consistency in measurements.

Now we're not talking about the sort of measurements you make with a ruler, since discrepancies of a small nature don't tend to matter a whole lot. No, we're talking about the sort of measurements made with fine measuring instruments such as micrometers or vernier calipers.

Now, the discussion that was going on was with reference to the best clearance to run between the bore and piston for a given piston type for race or street purposes. I hade quoted figures that I generally use for both situations for forged and for cast piston types. Read more

A subject worthy of an entire book to explain the whys and wherefores, and also causes much consternation on the part of the transplanter. Terminology - BBU - Big Bore Unit SBU - Small Bore Unit FD - Final Drive (diff ratio) A subject worthy of an entire book to explain the whys and wherefores, and also causes much consternation on the part of the transplanter. Much confusion’s spread over which gearbox has the best ratios, is best to use, and with which FD. For a detailed account on this and covering all gearboxes fitted as standard to the Mini, see the relevant separate articles 'Gearbox - Standard production gearbox types'. Fortunately, when selecting a complete engine and gearbox unit from a Metro, the gearbox will pretty much suit the engine and be easily transplantable whole into the Mini. It shares exactly the same rod-change linkage as the Mini. Difficulties only arise when fitting a rod-change gearbox into a pre-1973 Mini that has the old remote-type gear-change mechanism, but not insurmountable. It's dealt with in the 'Ancillaries' appendage to this series. Read more

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings.

Terminology -
BBU - Big Bore Unit (1275cc based engines)
SBU - Small Bore Unit (850/998/1098cc based units)
FD - Final Drive

NOTE: This information is largely for transplanting large-bore engine units into small-bore engined Minis. For further information on up-grading transfer (drop) gears, refer to relevant separate article.

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings. Read more

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek),

Terminology -
BBU - Big Bore Units
SBU - Small Bore Units

NOTE: This information is largely concerned with transplanting a large-bore engine into a small-bore engined Mini. For further information on clutch and flywheel assemblies in particular, refer to relevant separate article.

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek), and ‘top-hat’ plunger and rod bearing operation. Read more

What they don’t tell you in the manual! Terminology - FD - Final Drive (diff ratio) What they don’t tell you in the manual! If you’ve decided the FD fitted isn’t what you want, changing the FD is possible without separating the engine from the gearbox. Removing the diff case will allow you access to the diff assembly to change the crown-wheel, and access to the gear-change linkage. Use a manual for crown-wheel replacement. While you’re in there it would be just as well to replace the thrust washers and diff-pin as these are the source of many a gearbox problem. Particularly for up-rated engines where fitment for the competition diff-pin is highly recommended. Once again, follow the manual here. Now the bit they don’t tell you how to do... Rod-change types - Removal of the speedo drive housing gives access to the pinion retaining nut (1.5”AF socket needed and a long bar). To be able to undo the pinion nut (torqued up to 150lb ft !!) you need to engage two gears - 2nd and 4th - to lock the transmission. Read more

Install engine. It is absolutely imperative that the cooling system is more than sufficient to deal with any temperatures likely to be produced by the engine. More power means more heat to be dissipated. A standard radiator is very unlikely to be able to cope with a reasonable power increase over standard.

Do not fill cooling system yet. Set clutch throw-out and free-play take up. Double-check all connections electrical, oil, fuel and cooling system. Put in engine oil – use a cheap multi-grade mineral oil. DO NOT use either semi or full synthetic oils. They will stop the rings from bedding in. Remove spark plugs, and spin engine over in bursts of a few seconds to pick up oil pressure and prevent starter motor damage. DO NOT start engine until oil pressure picks up.

Once oil pressure is showing, check ignition timing statically. Set to figure advised by distributor maker, or if no figures available, set at around 6-8 degrees BTDC. Re-fit spark plugs and start engine. Read more

The widespread and prolific fitment of Metro engines into Minis - usually those endowed as standard with small-bore (850/998/1098) engines - practiced in the UK has been spreading to many other countries worldwide.

So it's not surprising that the most commonly asked question has also become more prolific concerning the fitment of said engine - apart from actually how to manage the transplant and the differences in the installations, covered in articles relevant article on this site - is just which type of engine the individual concerned has bought or what they already have fitted to their car and is it worth keeping or junking. One initial question I pose often draws a pregnant silence whilst said inquiree scrambles their brains trying to find an answer for. Following that protracted pause, 'I dunno' is the usual answer. I then have to get into a lengthy explanation as to how to determine what said engine is. Read more

DIY enthusiasts often believe that building an engine to give excellent all-round road performance is beyond them. Mainly from comparisons made between what they have been able to achieve and what specialists say should be achievable from any particular type of engine build.

Generally scrambled further by the non-perfect match of parts and components used between aforementioned specialist and erstwhile DIY-er, and the ritual 'nose-tapping and knowing winks' display of those specialists. Something you can very nearly 'see' even when talking to such folk on the phone - or that inimitable 'ah, yes, well…' So some form of 'black art' is implied. Whilst there is most definitely a degree of 'feel' involved between the real specialist's results and those of just a good engineer - the bones of the deal is subject to no such thing and is certainly within the capability of the DIY enthusiast given the necessary information. And that has been the problem. Read more

The 998cc engine is a very robust and tunable unit. It is also the most common engine found in standard Minis. Despite the lure of the much-advertised 1380cc alternatives, many simply want to get a little more from what they have at reasonable outlay.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money. Read more

To maximise power and economy potential from any engine, burning the compressed fuel/air mixture at precisely the right point throughout the engines entire rpm range is essential.

Terminology -
TDC - Top Dead Centre
BTDC - Before Top Dead Centre
Dizzy - distributor
CR - compression ratio

To maximise power and economy potential from any engine, burning the compressed fuel/air mixture at precisely the right point throughout the engines entire rpm range is essential. This ‘point’ is generally somewhere before the piston reaches TDC on its power stroke described in degrees - i.e. 10 degrees BTDC. This point isn’t constant throughout the rpm range. Low rpm values are normally less than high ones.

Ultimately the dizzy provides this spark at exactly the right point to effect this burn. Read more