£217.80 exc vat
£261.36 inc vat
In stock
£217.80 exc vat
£261.36 inc vat
In stockRecommended usage 1 x C-AHT776 to fit one mini.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Smarten up your engine bay with these stainless steel nuts which are not only stronger and resistant to rust but the multi point nut heads are easier for access. See also kit C-STR287.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Split Weber manifolds, pair, by Maniflow, Steel, 3 3/4" long, upswept.
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
Stainless steel version of C-AEG376. Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex,simulating a pulsing effect similar to the outside two pipes,thus producing an improved B...
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Genuine Weber 45DCOE Carb, calibration from the factory is as below:
Choke 36
Throttle Plate Angle 78 degrees
Auxiliary Venturi 4.5
Needle Valve 200
Main Jet 145 Pump Jet 45...
Large bore LCB for competition use or on very large bore street engines; such as 1400cc+. Y-piece outlet end is 2" outside diameter, 1.875"id.
The best quality production exhaust manifold available from Minispares. The Long Center Branch...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
Known as a swinging needle because they sit on a spring which locates into the hat/cup end of the needle and have sideways movement.They start with part number prefix CUD for HS type carbs--NZX for HIF carbs--the earlier H and HS type were fixed soli...
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
Our heavy duty throttle cable is superior in many ways.
A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.
Cable to carb bolt is ACC5062.
Master carb rebuild kit
Twin 1 1/4" SU carbs were stock on Cooper S and most Spridgets and are popular upgrades on many cars. The reason they are so popular is that the design is fantastic- but let's face it people; everything wears out and...
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.