£247.50 exc vat
£297.00 inc vat
In stock
£247.50 exc vat
£297.00 inc vat
In stockRecommended usage 1 x C-BTA1005EVO to fit one mini.
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
This is the original Evolution"Cross-pin" differential for the Mini.
Produced and sold by Mini Spares since 1994. It is a super heavy duty differential designed as a significant upgrade for reliability and strength to the standard units. Ove...
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current tec...
Straight cut drop gears are the most durable arrangment that can be fitted to a transverse A-series powerunit. These 3 gears are responsible for transferring all the Hp from the motor to the gearbox, so their longevity should be a top priority for an...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...
Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 ...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1
24...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
Pre A plus 4 synchro laygears had 2 of these fitted plus a small bearing whereas the A plus laygear had only one.
Dual use bearing fits the end of the A Plus 18mm mainshaft where the Ist Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.
Knowm as the 18mm bearing it was Rovers upgrade on using larger mainshafts and laygears wit...
Genuine Rover Xparts item. See BHM7012 which many vendors sell as their GSV1073.
In board CV joint(pot joint)gaiter kit metal clips and grease.
The single largest reason for the failure of this rugged assembly is contam...
Minispares recommend this central oil pick-up be installed with every transmission rebuild.
The original Mini oil pick-up pipe lives in the right hand edge of the gearbox casing, which is okay if you are driving straight. But during a right ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.