£35.48 exc vat
£42.58 inc vat
In stock
£35.48 exc vat
£42.58 inc vat
In stockRecommended usage 1 x TRAN0007 to fit one mini.
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
IF YOU EVER STRIP ONE OF OUR C-AJJ3385 CROSSPIN DIFFS DOWN THIS IS THE LONG MOLYBDENUM COATED PIN THAT THE PLANET WHEELS RUN ON.
IF YOU EVER STRIP ONE OF OUR C-AJJ3385 CROSSPIN DIFFS DOWN THIS IS THE SHORTMOLYBDENUM COATED PIN THAT A PLANET WHEEL RUNS ON.
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
This is the original Evolution"Cross-pin" differential for the Mini.
Produced and sold by Mini Spares since 1994. It is a super heavy duty differential designed as a significant upgrade for reliability and strength to the standard units. Ove...
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly
Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...
The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts
Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.