Wheel cylinder repair kit for the very first Minis with one cylinder per front wheel only. 15/16" Please note you will need 2 kits per wheel cylinder as only 2 seals are supplied.
Easy bend copper pipe with 2 male unions 14" long which fitted most single line dry suspension cars from the brake master cylinder to the 3 way valve - the left hand drive version is 32"long - some people use the HF12 but originally it w...
This Genuine AP 3 way connector was used on the diagonal split braking system joining the front brake pipes to the main line system on both sides of the car, hence 2 fitted. On later dual line cars, with the pressure valve on the bulkhead (1978 on), ...
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
Easy bend copper-nichel brake pipe kit for L/H/D front to rear split system,also with pipes for drum brakes for pre 84 cars. the m/cyl pipes are longer and only for GMC227 with 12mm lower union--if older type B/M/cylinder a 10mm both end...
HYDROLASTIC WITH SERVO and includes 2 front wheel cylinder bridge pipes if required. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good idea to check your metal brake line...
Brake hose kit to convert Metro calipers to fit single line mini systems. This kit contains two short braided link pipes, two long braided hoses, two banjo bolts and the copper sealing washers.
Plates for protecting the brake hose to the front calipers as used on works cars. Sold as a pair.
Copper easy bend 10" long metal pipe with male and female end fittings to fit between rear wheel cylinder and flexible hose on dry suspension models. These pipes are retail less 35% discount at least to keep prices viable.
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis.
Dry suspension single line system brake pipe kit with servo pipes for saloons.
Does not include 2 front wheel cylinder bridging pipes pipes HF10 for drum brakes. These kits or pipes are at least 35% off retail
Brake hose for models with disc brakes.Beware of very cheap imports. We all believe that our life often depends on our braking system. But how can you tell when "it's good enough"? The flexible rubber brake hoses are a prime area for concern. The ho...
Servo to 3 way on Cooper S R/H/D and L/H/D except 1275GT(30" HF32)-Easy bend copper brake pipe 24" long with 2 male ends. These pipes are retail less 35% discount at least to keep prices viable.
All MK1/ MK2 Minis including all Cooper and "S" versions plus MK3"S" only.
This valve was fitted to every MK1/2 car including Cooper and "S" and the MK3 Cooper "S" only.
All other MK3 versions 850/998/1100 use 21A2031 w...
This holds the brake light switch(C16062A) on single line brakes and fits into the 2 way union where the front hose bolts on the other end. Later cars with no switch use C5192A.
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis. These kits or pipes are at least 35% off retail.
Single line R/H/D brake kit for hydrolastic suspension cars without a servo, including the 2 front wheel cylinder bridge pipes.If you have a servo see kit GB5002.
You'd think that the way Minis leak oil they'd never rust on the ...
Diagonal split van/estate only 1976-80-see GB5014 for saloon kits which now have imperial connectors and all imperial pipe unions.
You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your ...
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.