If you want to prevent disaster, you should check your driveshaft joints before they self destruct. The best and easy way to do that is to listen and feel the car as you lift off the throttle while getting off a fast road/motorway etc. If you feel a...
Mini Spares own stamped GCV1013. Brand new CV Joints with gaiter, hub nut, grease and clips. Stamped with our part number GCV1013 for identification from may 2014 to denote our authenticity of this top quality joint, sold singly.
These are t...
One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...
Special circlip to hold the hardy spicer output shaft into the LSD units
such as evolution and Salisbury.
Steel driveshafts with original circlip holes, ensure that the cv circlip clicks fully in both shaft and cv joint.
These are upgraded to stop the ends twisting off. Available for rod change also as C-BTA1264 SOLD AS A PAIR
Larger diameter competition driveshafts for use with Hardy Spicer output shafts only. Must be used in conjunction with the larger Allegro/Maxis outboard CV joints 37H7869. these come with the required clips
Special grease for Cv joints and any homokinetic joints. Enough for one joint only.
HEAVY DUTY AXLES! The Mini drive shaft or half axles are different from side to side. This, the right side one is the longer of the two. Now for the most part the Mini axle is very long lasting but that is not to say that you can neglect them. The ...
Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is 2A7323.
Allegro CV joint. These are the larger Allegro CV joints that some competition cars use, they fit Mini hubs but need the larger driveshafts C-BTA1266.
This spacer fits only on the drum brake type drive flange 21A231. It has a champer which fits against the flange correctly. Also used on 997/998 Coopers which had a different drive flange but the same smaller nose cv joint.
Top quality nut unlike many sold with CV joints from china.
For genuine nut See BTA249 also. Sold singly
Mini Spares own quality product from original drawings in EN24 material for 7.5" wide disc set ups.
The Mini Cooper "S" drive flange as used on all 7.5" disc Cooper S/1275GT variants was originally intended to use 10" wheels as an integral p...
Inboard CV (pot joint) splitting tool used to remove the constant velocity joint from the gearbox by way of driving this wedge-like tool between joint and gearbox. Does not remove joint from driveshaft.
Rubber U-joint for yoke-type driveshafts. These are the only new supply available except for QL5000 alternative.
The very early Minis used the rubber U-joint drive couplings to eliminate harshness being transmitted to the passen...
Cheaper alternative to genuine timken front bearing kits.
These are very well tried and the best of any of non genuine bearings available.
Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1...
Special Tuning hit upon this idea to stop the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the stee...
Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal 22A1566
This is Minispares version of the Metro vented disc type drive flange, made without the original Metro wheel centralising lugs.
The wheel centralising lugs as originally used on the Metro have been removed to allow the fitment of all types o...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.