($43.20) £43.20 exc vat
($51.84) £51.84 inc vat
($43.20) £43.20 exc vat
($51.84) £51.84 inc vat
:Used: (secondhand) 5 tooth drive spindle mainly used on Metro range but includes ERA turbo mini with 3.2 final drive using 16 tooth plastic pinion.
Obsolete new but offered "used" in case a ratio change is required. The only drive spindle ...
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
NO LONGER MADE" see 22G2024MS for 18 tooth red Metro speedo pinion as used with 5 teeth drive,now obsolete from Rover but 22G2204MS is offered as used secondhand items in case ratios require changing. -Combinations are listed on our webs...
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
Oil seal for speedo drive pinion cover (DAM8488)
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from aero quality steel making it 20% tougher.16x60 teeth count.
Always Check...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET. ($54.35) £54.35 exc vat ($65.22) £65.22 inc vat
See table of "Straight Cut Gear Kits" and their components
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Straight cut reverse gear for rod change box. Has 16 and 18 teeth. ($69.90) £69.90 exc vat ($83.88) £83.88 inc vat
See table of "Straight Cut Gear Kits" and their components
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
This is the large clutch case gasket that is made to a special thickness.
Many companies who copy these gaskets are not aware that the gasket thickness and consistency is important as it affects the clearance on the idler gear shimming. This...