£15.00 exc vat
£18.00 inc vat
In stock
Obsolete new but offered "used" in case a ratio change is required. The only drive spindle ...
£15.00 exc vat
£18.00 inc vat
In stockRecommended usage 1 x 22G2022MS to fit one mini.
Follow your speedo cable to the gearbox and it screws onto an alloy housing bolted to the gearbox. This is the gasket between the housing and the gearbox.
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Koyo bearing that sits inside early 3 synchro 1st motion shafts.
USED yellow colour coded 7 tooth splined speedo drive (23.4mm diameter worm)that fits in the gearbox to drive the TXD10004 15 tooth pinion that the speedo cable fits on and drives. Different helical pitch to other 7 tooth drive pinions.S...
:USED: Speedo cable drive pinion in the gearbox with 17 teeth, it was used with a 6 tooth drive spindle on all 10" wheel cars pre 1980.
Either brown or plain white sort of colour about 20.50mm to 21.12mm in diameter and very similar to [lin...
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Fully floating primary gear bush to downsize from our 1275cc type to 998 size on our 1275 primary gears with circlip conversion only to fit small bore crankshafts. Mainly used for our straight cut primary gear with circlip to hold fully floating bush...
Plunger dowel for use with GAE131 reverse light switch on early gearboxes pre rod change.A fibre isolation washer must be fitted for switch to work which is available as 1B3664
Genuine Mini Spares product, fits 3 and 4-synchro gearboxes except for rod change types which use GAE191. This switch replaces the plug on the front of the remote-shift transmission case. It is triggered internally by the shift linkage w...
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
"USED" units always available This front cover is where the speedo cable drive gears are fitted and fits all Mini manual transmissions. They might have a few extra pieces on them such as studs and pinion cover late. These were over £97-00 when availa...
The 25.4mm wide original genuine bearing to take 19.05mm size idler gear shaft and sits in the gearbox case on early 3 synchro types and also in the early type clutch case. There is a cheaper version on the market but for gearbox safety sake we have ...
Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.
The 6 longer ones are 22A152.
These st...
Gearbox oil strainer to gearbox internal case gasket and also used on the C-AHT54 special oil pick up pipe. One also sits on the outer plate held onto the gearbox outer casing by 2 screws.
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.