EMMISSION VALVE RUBBER DIAPHRAGM FOR 13H5191
27H7758

($4.50) £4.50 exc vat

($5.40) £5.40 inc vat

In stockIn stock
The rubber diaphragm that sits in the exhaust emission valve.known as the clacker valve on Cooper S and some variants/It sat on the inlet manifold and a clip holds the top on to where this rubber sits, This diaphragm is not suitable for the raised lid type fitted from 1966.

Fits the later flat type lid 13H5191

($4.50) £4.50 exc vat

($5.40) £5.40 inc vat

In stockIn stock

Recommended usage 1 x 27H7758 to fit one mini.
Closed Circuit Breathing Components and Gasket Set - Qty 1

Alternative products

This very commonly used device has been very uncommon to find. We now have them! The valve is needed on nearly all twin carb models such as MG

Midget, MGB and of course Cooper S models to pass emissions control tests. A properly operating ...

People also bought products

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

Also denoted by its black plastic base. Twin HS4 carbs have 30 degree float bowl angles and therefore this jet is easier to fit as it is longer. L/H carb uses AUD9098A std single HS2 jet.



For...

Linkage set for Converting from waxstat to standard type jet for one single carb .

For 21A2331 pipe. Before the days of Aeroquip, Minis had braided petrol pipes. They should be used in place of rubber for all fuel lines where possible. This is 5/16" bore size for the joining pipe on twin tanks using the original pipe ...

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

Fuel or water T piece adaptor

used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

this is the plain butterfly disc for the HS4 1.5" carb and if you have the air valve type butterfly disc see WZX1325

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

spindle threaded both ends for HIF44 for most late carbs--see WZ1127 for spindle with thread one end only as per early metro cars. Thread size is 1/4 BSF

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

jet assembly (0.100") for the HIF44 carb only- see MGM10008 for HIF38(0.090")

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

Originally quoted as the HS2 twin carb manifold stud it is one thread longer than CHS2613 which was for single HS2 and spin on oil filter head to the block. UNC course thread for manifold or block and UNF for th...

The little spring that sits at the end of a spring loaded carb needle on late HS and all HIF carbs where applicable.

For HS2 single carbs this is the Complete kit of the parts required for an overhaul kit- if you do not require the spindle and disc and bushes see WZX1851

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

This is...

Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...