($32.00) £32.00 exc vat
($38.40) £38.40 inc vat
In stock
C-AHT770 takes 1.5" AND 1.75"carbs. Medium size port runners suit all small bore engines, and large bore engines up to fast road spec (dependent on head intake port size).
The plug 5/8UNF (supplied with manifold) should be thread locked into the manifold, with care taken not to wind all the way down.
Sales are 900-1000 per year as all tuners use this manifold so it must be good.
If you are using a thick carb spacer use the CHS2515 studs which are slightly longer.
($32.00) £32.00 exc vat
($38.40) £38.40 inc vat
In stockRecommended usage 1 x C-AHT770 to fit one mini.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
This plug fits our inlet manifolds and Rover types with servo take off holes..
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
3.5" long steel intake manifold by Maniflow for Weber 45 DCOE/DHLA.
Smarten up your engine bay with these stainless steel nuts which are not only stronger and resistant to rust but the multi point nut heads are easier for access. See also kit C-STR287.
Aftermarket union for fitting all mini inlet manifolds where a take off is required for your brake servo or emission valve on Cooper S cars.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Split Weber manifolds, pair, by Maniflow, Steel, 3 3/4" long, upswept.
Spacer block between carb and manifold for single HS2 carb. To use on twin carbs the fixing holes need drilling out to size. 7.5mm thick
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Cast alloy type, Fits either twin HS4 or HS6.(requires modifacation to fit HS6.2 extra studs per carb)
This intake manifold for twin SUs has been carefully produced to minimize cross-port-flow interference caused by t...
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
Cast alloy type,this intake manifold for twin 1.25"SUs (H2 or H4 -- NOT HS4)
It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places. Further blending ...
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
Standard bore LCB (1-3/4" id) for standard to high performance 1275s and for street 1380s. This is the same manifold as the standard C-AEG365 but with a slightly different shape to allow fitment to cars fitted with rubber coupling drives...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Stainless steel version of C-AEG376. Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex,simulating a pulsing effect similar to the outside two pipes,thus producing an improved B...
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.