REAR SUBFRAME FITTING KIT INC TRUNNIONS PRE 1976
MS42

($67.50) £67.50 exc vat

($81.00) £81.00 inc vat

In stockIn stock
This kit contains all the parts from MS44 plus the 4 cast trunnions that hold the rubber bushes. This complete rear subframe fitting kit is what the factory fitted to minis up to 1976 on but the later kit MS41 will fit early cars if fitted as a complete kit.

Rubber Bushes are made in the UK.

($67.50) £67.50 exc vat

($81.00) £81.00 inc vat

In stockIn stock

Recommended usage 1 x MS42 to fit one mini.

Alternative products

complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43

Rubber mounts are made in the UK.

Kit contained products

This is the correct thick flat washer for a suspension tie bar rod. The washer has a 7/16" hole is 1.5" wide. See 2A4328 for the correct dished washer.

Mini Spares product is a better quality pin-Please note that only the pin is supplied. Please see 2A5818MS for the bushes.

2 required per car

Minis Spares product to a slightly higher modern day shore hardness and texture soecification.

Pre 1976 used 8 of these bushes for the trunnions on the rear subframe but from (MK4)1976 on Rover reduced the quantity to 4 and used 2 larger bus...

This is the larger 5/16" unf that goes though the rear subframe mounting trunnion. Cars manufactured before 1976 require 4 of these, after 1976 require 6. Sold individually.

Front subframe to front teardrop mounting, clutch case to block.

Engine mounting to subframe - easier to use than the GFK5184 - 3/4" long

Mini Spares product,metal trunnion to hold the 2-2A5818MS bushes on the rear subframe.

Originally there were 4 of these trunnions on the subframe but in 1976 (MK4)the front 2 brackets were strenghened and enlarged to [link]21A2...

People also bought products

All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.

New Evolution design in 4mm thick metal mase to fit Genuine and our non genuine subframes better than the standard originals.

The amount a wheel leans in or out at the top is called "camber". As the car turns and the body leans the tire can ...

This is the metal packing piece for the twin bolt pre 76 front dry subframe tower mount.

Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.

Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...

This is a budget way of improving the stability of the front subframe leaving the rear mountings standard for quietness.

It only includes the 4 poly tower spacers and for the front of the front subframe 2 poly spacers and 2 metal washers.

Minis Spares product to a slightly higher modern day shore hardness and texture soecification.

Pre 1976 used 8 of these bushes for the trunnions on the rear subframe but from (MK4)1976 on Rover reduced the quantity to 4 and used 2 larger bus...

To compliment the top alloy blocks (C-STR640), those troublesome front rubber mountings can be replaced by alloy cast mountings which will not break and further enhance roadholding. These are for the front of the front subframe on vehicles built from...

The set of four aluminum top front subframe mountings are to replace the standard rubbers fitted on vehicles from 1976 to present date. These alloy pads help reduce subframe movement, which is detrimental to handling when driven hard. As the original...

Genuine correct length with cut outs and drain holes in the correct places.

The MK3 door seal is notable because of it's large 'bulb' area. The 'bulb' is the round section that the door closes against. The size is determined by how much gap ...

complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43

Rubber mounts are made in the UK.

The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...

The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 used the same bush 2A5818(C-STR638) at the front and rear of the subframe, ...

Mini Spares product is a better quality pin-Please note that only the pin is supplied. Please see 2A5818MS for the bushes.

2 required per car

Rear solid brackets for the front subframe of post 1976 models, ideal for racing or road if noise is not important. But very important if you are after the ultimate handling! we have tried the poly type but they were not as successful.

Every nut, washer, bolt, rubber bush and 2 pins that hold the rubber bushes that are prone to rusting badly and are required every time you do a subframe change. Including the 2 large penny washers this kit has 36 components. Other companies offer l...

Towing eye that fits in place of the bolt holding the front panel to the subframe. For stronger later version see KPU100160.

When using certain accessory tow bars make sure the towing eye is in the right position to suit or it w...

Used in our MSSK001 left hand lower engine stabiliser kit this bracket fits to the subframe and the gearbox.

This is the rear bracket welded to the rear subframe for the later rubber strap mounted exhasts from late 1991 on use

Mini Spares product,metal trunnion to hold the 2-2A5818MS bushes on the rear subframe.

Originally there were 4 of these trunnions on the subframe but in 1976 (MK4)the front 2 brackets were strenghened and enlarged to [link]21A2...