SINGLE PISTON RING SET FOR R32026-30

($10.62) £10.62 exc vat

($12.74) £12.74 inc vat

PISTON RING SET 998cc 89 ON PRESSFIT

R43240-00

Standard Size with 0.59" compression rings and 0.1181" oil ring for 998cc

($81.60) £81.60 exc vat

($97.92) £97.92 inc vat

+20 RINGSET FOR MEGA & OMEGA PISTONS 1275cc

C-AJJ3379-20

AE Hepolite +20 Engine set of rings for C-AJJ3378/20 C-AJJ3382-60 Mega and Omega pistons when rings are 0.0470"(1.2mm) and 0.1575" 4mm oil rings.

For latest spec race quality NPR rings see C-STN102-20

($49.46) £49.46 exc vat

($59.35) £59.35 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat

TIMING CHAIN SINGLE ROW SPECIAL QUALITY

3H2127EVO

Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.

This chain saves all the time and effort requ...

($22.05) £22.05 exc vat

($26.46) £26.46 inc vat

BIG ENDS PLUS 40 OVERSIZE 998/1100 COOPER S

AEB572-40

Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

( Tri-Metal )

Sintered copper lead...

($28.02) £28.02 exc vat

($33.62) £33.62 inc vat

BIG ENDS PLUS 30 OVERSIZE 998/1100 COOPER S

AEB572-30

Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

( Tri-Metal )

Sintered copper lead...

($22.96) £22.96 exc vat

($27.55) £27.55 inc vat

SIMPLEX TENSIONER 6 PIECE KIT

MSSK051

Parts required to stop timing chain rattle on A plus engine with single row chain.Last chance to buy the plate and pin to hold the tensioner as they are

obsolete from Rover.

It is worth the expence to fit MSSK051EVOkit...

($21.06) £21.06 exc vat

($25.27) £25.27 inc vat

998/1100 MAIN SHELLS PRE A PLUS - MAHLE

VP733-00

Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at standard size. Early 850 mains were VP592 and 1.185" 30.10mm wide..Quantity required-1 set.

($30.00) £30.00 exc vat

($36.00) £36.00 inc vat

CRANK BOLT LONG CAPHEAD WITH AND SPECIAL WASHER

C-AHT147

A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...

($8.91) £8.91 exc vat

($10.69) £10.69 inc vat

MAINS SET 30 OVERSIZE 998/1100 upto 1985 with all ...

AEM3314-30

Main bearings for the crankshaft as preferred by performance engine builders 30 thou oversize pre 1985

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

($27.00) £27.00 exc vat

($32.40) £32.40 inc vat

MAINS SET 10 OVERSIZE 998/1100 upto 1985 with all ...

AEM3314-10

ACL Main bearings for the crankshaft as preferred by performance engine builders 10 thou oversize pre 1985

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

($24.00) £24.00 exc vat

($28.80) £28.80 inc vat

BIG ENDS SET STANDARD 1275 EXCEPT COOPER S

AEB91306-00

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

($28.50) £28.50 exc vat

($34.20) £34.20 inc vat

CRANK PULLEY DAMPER ONLY "S" (MUST BE BALANCED TO ...

12A367

For high performance engines an efficient crank damper is a necessity to reduce failure. The standard damper commonly used is barely adequate for the standard engine. Mini Spares has reproduced the original "S" damper and pulley-far superior to the s...

($67.50) £67.50 exc vat

($81.00) £81.00 inc vat

DUPLEX TIMING CHAIN.DOUBLE ROW ENDLESS

2H4905

For race quality chain see 2H4905EVO.

It only makes sense that if you have your engine out of the car that you replace the timing chain. The chain controls the timing of the camshaft and even a slight amount of wear or stretch c...

($5.78) £5.78 exc vat

($6.94) £6.94 inc vat

MAINS SET 10 OVERSIZE PRE A PLUS/EARLY A+ 1275

AEM91120-10

Main bearings, 1275 2" mains. 10 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

ACL branded

($30.00) £30.00 exc vat

($36.00) £36.00 inc vat

PRE A+ 848/998/1098 CORE PLUG

2K8169

Convex type core plug at 41.4mm for all early A series blocks up to A plus.

4 required per engine-these are known as the flat type wher the centre has to be pressed in so the convex plug spreads out. The Cooper S althouh same size was a cup ...

($0.85) £0.85 exc vat

($1.02) £1.02 inc vat

CAMSHAFT GEAR LOCKTAB

2A759

If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.

($0.52) £0.52 exc vat

($0.62) £0.62 inc vat

BLOCK GASKET SET SMALL BORE PLUS COOPER S

AJM202MS

Mini Spares own Universal gasket set.

This engine block gasket set fits all manual blocks and include rubber tappet chest covers and bolt seals, also including A plus and Pre A Plus timing gear and cover gaskets. For the equivalent gasket se...

($12.75) £12.75 exc vat

($15.30) £15.30 inc vat

CAMSHAFT TRIANGLE PLATE

AHU2379

Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...

($5.50) £5.50 exc vat

($6.60) £6.60 inc vat

CENTRE MAIN STRAP & BOLTS - 998cc BLOCKS

CMS10

Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...

($8.94) £8.94 exc vat

($10.73) £10.73 inc vat