TIMING COVER GASKET A PLUS
12G2625

(1,60 €) £1.60 exc vat

(1,92 €) £1.92 inc vat

In stockIn stock
Timing cover gasket with 11 holes for cars with timing chain tensioner bulge as standard on all A Plus. We recommend fitting the more expensive original genuine type with anti leak seal for longevity see GUG705550GM.

Pre A plus gaskets only had 10 holes.

Tip-When fitting make sure all bolt holes line up through gasket and ensure you only do bolts up lightly and alternatively to start with, (larger bolts first) because doing one up tight before moving on to the next one can cause distortion to the gasket and split slightly which under heat and cooling of the engine can eventually cause tears.

correct torque setting- 1/4"dia unf bolts 4-6lb.ft kg.m 0.55-0.83

5/16"dia unf bolt 10-14lb.ft kg.m 1.4-1.9

(1,60 €) £1.60 exc vat

(1,92 €) £1.92 inc vat

In stockIn stock

Recommended usage 1 x 12G2625 to fit one mini.
Timing Cover & Tappet Inspection Cover - Qty 1
Timing, side plate and rocker covers - Qty 1

Recommended products

Improved oil seal in Viton introduced on injected cars to erase crankcase emmissions causing oil leaks. This timing cover oil seal aslo has a different shaped lip to discourage oil leaks and will fit all A series engines.

Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...

Alternative products

Genuine Timing cover Klinger gasket with screen sealant strip to stop leaks for cars with timing chain tensioner bulge as standard on all A Plus.

Definitely worth the extra cost for longevity on your valuable classic mini

Tip-When ...

Kit products

Parts required to stop timing chain rattle on A plus engine with single row chain.Last chance to buy the plate and pin to hold the tensioner as they are

obsolete from Rover.

It is worth the expence to fit MSSK051EVOkit...

Parts required to stop timing chain rattle on A plus engine using special anti stretch single row chain 3H2127EVO.Last chance to buy with the plate and pin to hold the tensioner as they are obsolete from Rover.

Fitted to 998/110...

People also bought products

High quality silicone version of 12A1358. Fits all A series and A+ rocker covers.

A kit to convert the early style cartridge oil filter to the later style spin on filter.

Ramair’s hugely successful range of filter kits, designed to bolt directly to the carburettor body, is used widely in both competition and street applications. The element is of sturdy construction, supported by a stainless steel cage and provides ma...

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

This is the large seal for the early type oil filter assembly pre spin on type.

Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

Race quality single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.

sold per piston so 4 packs required per engine

Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.



Sold per piston so 4 packs required per engine.