(12,38 €) £12.38 exc vat
(14,86 €) £14.86 inc vat
In stock
47H9535M can be glued to this to stop the tank moving
(12,38 €) £12.38 exc vat
(14,86 €) £14.86 inc vat
In stockRecommended usage 1 x 21A1329 to fit one mini.
Lower short half of the strap is used on the earlier 5.5 gallon strap and goes around the circumference of the tank as opposed to the later 7.5 gallon tank where it goes across diagonally. The longer upper strap is 2A2226 and both are us...
This long upper half of the strap is used on the earlier 5.5 gallon strap and goes around the circumference of the tank as opposed to the later 7.5 gallon tank where it goes across diagonally. The shorter strap is [link]2A2231[link/] and both are use...
Anchor bracket that fits to the rear seat bulkhead to hold the petrol tank retaining straps on R/H extra tank when fitted.
Non Genuine petrol tank neck seal, we advise fitting 14A7057GENUINE for extra longevity, quality, looks and a much better fit where we seem to be the only company offering a quality part, from our own tooling made in the UK.
Thi...
Support bracket for the R/H, genuine Heritage part, can also use our own bracket 21A1329.
Want to add a right-hand tank to your one-tank Mini? This kit includes everything, except the tank, to do it. Included are retaining straps, support brackets that mount to the rear seat back and boot floor, between tank metal fuel line and braided fu...
5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
5.5 gallon left hand tank with twist in sender unit.
For all mini saloons from 1964 until 1980 except Elf and Hornet. Also except the 1275GT from 1974 which used the later 7.5 gallon tank which became standard fitment to all mini saloons fro...
Support bracket for the R/H, genuine Heritage part, can also use our own bracket 21A1329.
Gasket/seal for mounting the fuel pump to tank for SPI and MPI Mini's
If you've ever changed a fuel filter on an injection car you may have noticed you need to remove the whole bracket in order to remove the filter as the securing bolt is on the wrong side for good access, this is because the bracket was originally use...
This is a copy of one of the best looking gas caps you will ever add to you car. Polished chrome with a flare. The "'flip top' and 'push button' opening cap was made famous by some of the most historic cars ever raced at such famous tracks as 'Monz...
Vent pipe from petrol tank
late cars were only 765mm or 31" approx, but Mk1 cars were 54"
For 21A2331 pipe. Before the days of Aeroquip, Minis had braided petrol pipes. They should be used in place of rubber for all fuel lines where possible. This is 5/16" bore size for the joining pipe on twin tanks using the original pipe ...
Metal petrol pipe with tank union, this is for all estate and van versions with a mechanical pump where a long full length pipe is required. Made in non rust
metal.
Designed to look expensive this 60s look cap fits over the genuine Rover locking cap WLD100660 held on by grub screws. Polished alloy finish similar to the Aston or john Cooper cap it is ultra easy to install and looks fantastic. Flip to...
Fuel or water T piece adaptor
used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications
Saloon petrol tank retainer clip for the rubber seal on the sender unit which is ARA1502 .Early tanks had 6 screws holding the sender unit in place and used gasket GUG705711GM
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
This is...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Sponge like cushioning seal for all minis between the tank neck and the body plus the minivan/estat/pickup petrol tank where it goes between and tank and the the floor/shroud.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.