(18,30 €) £18.30 exc vat
(21,96 €) £21.96 inc vat
In stock
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thinner tail crankshaft and different primary gear.
(18,30 €) £18.30 exc vat
(21,96 €) £21.96 inc vat
In stockRecommended usage 1 x 22A451 to fit one mini.
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
Replacement bolts for securing the DAM5921 to the AP verto clutch unit only. 6 required but sold individually.
Torque figure should be 40-45lbft not to be confused with the pressure plate to flywheel bolts which are 18lbft.
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.
small face with numbers stamp-face outwards, larger surface aera side face flywheel.
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...
Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.
This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...
Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.
Clutch diaphragm, blue for 1275/1100/998/850 Mini, pre Verto.
This part superseded the GCC102 850-1100 diaphragm.
There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.
Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...
Long Pre Verto clutch arm.
Ensure you adjust the clutch properly otherwise the hydraulics are powerful enough to bend the ball end of the clutch arm, whether it be an old genuine or a new Mini Spares part. Replaces the old thin arm version 2...
FOR ALL 1300cc verto clutches which are 190mm wide
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.