LAYGEAR 3 SYNCHRO "S"
22G1100

(168,00 €) £168.00 exc vat

(201,60 €) £201.60 inc vat

In stockIn stock
3-syncro B type laygear which runs on needle roller bearings 88G396 fits the Cooper 998 Cooper "S" and Sprite-and was 22G232 until BMC stamped 22G1100.

Not only does the first gear end of the shaft typically take abuse but the ID where the bearing rides also will lose its surface hardening. If your gearbox makes a lot of noise it probably is this gear! This same laygear was used in the B type gears Spridget gearbox.

(168,00 €) £168.00 exc vat

(201,60 €) £201.60 inc vat

In stockIn stock

Recommended usage 1 x 22G1100 to fit one mini.
B Type 3 Synchro Mesh Gears - Qty 1

People also bought products

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...

Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...

The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise



fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play

Plunger dowel for use with GAE131 reverse light switch on early gearboxes pre rod change.A fibre isolation washer must be fitted for switch to work which is available as 1B3664

Mini Spares product Available again- 3 synchro B type gearbox 1st and 2nd synchro hub assembly for the mini. BEWARE -the outer track from the Sprite (22G1119) part of [link]22G1118[/link} is not reliable enough in a Mini gearbox as it allows balls an...

A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105

Genuine Mini Spares product, fits 3 and 4-synchro gearboxes except for rod change types which use GAE191. This switch replaces the plug on the front of the remote-shift transmission case. It is triggered internally by the shift linkage w...

This is the second gear 28 teeth as used on many 3-synchro Mini gearboxes. Introduced during the late 850 production and continued in use thru the "S" gearbox with the 22G1100 laygear. If you are inspecting your old gears be sure to ch...

Synchromesh spring for the 3 synchro gearbox. Fits 1st/2nd and 3rd/4th hub.

3 required per hub and 6 per gearbox.

Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings

Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.

Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.

Also the bolt to hold the starter motor.

Also the bolt for the [...

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.

Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.

If your gearshift lever transmits a lot of rattle and noise, replacing these three tiny but significant parts will likely cure it. The kit for the Spridget or Minor consists of the brass plunger (22A84) and spring (AEG3123) plus the nylo...