(257,62 €) £257.62 exc vat
(309,14 €) £309.14 inc vat
In stock
MADE FROM 409 GRADE STAINLESS.
(257,62 €) £257.62 exc vat
(309,14 €) £309.14 inc vat
In stockRecommended usage 1 x C-STR816S to fit one mini.
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
For the medium bore Maniflow LCB Y piece or AN180V. 48mm ID
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Smarten up your engine bay with these stainless steel nuts which are not only stronger and resistant to rust but the multi point nut heads are easier for access. See also kit C-STR287.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
This popular size clamp fits the y piece where it joins the manifold on all our standard long centre branch exhaust manifolds. Sold singly.
This is the clamp for the C-AEG365 manifold that clamps it to the engine for extra support.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
1 inch X 50 feet / 25mm x 15metres
For Race Use only!
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
Stainless steel Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s, and for street 1380s. And in stainless steel for long life!
There is NOT enough clearance room when fitti...
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
Standard larger 1.750" bore single box exhaust system for saloons.
see C-ARA339 for van and pickups.
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.