£12.00 exc vat
£14.40 inc vat
In stock
£12.00 exc vat
£14.40 inc vat
In stockRecommended usage 4 x 21A1496 to fit one mini.
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
one piece forged lower rod end arms
unbelievably at this price they are not the welded type as sold by many of our competitors
Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...
All models of the Mini use the same rear hub (this piece holds the rear wheel bearings). The Mini's rear wheel bearings are more than adequate, usually requiring only occasional repacking with grease. The weak link may be the cast iron hub; it is not...
Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.
General:See also c-AJJ3360 fully adjustable arms
Negative camber lower arms are specifically forged in different degrees to...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Complete rebuild kit for rear radius arm as sold by us since 2005.
Beware of cheap imports that are available in the market as they do not have correct heat treatment where required and have no longevity.
Kit Includes: shaft, beari...
The term 'hydro' in the renowned Cooper "S" suspension system "Hydro-lastic" means at least in part a liquid. This famous system was designed by BMC make for smooth and fluid ride while taking all of the abuse of off road rallying. It is not uncommon...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Mini Spares product from own original tooling since 1989.This small sheet metal panel mounts below the horizontal seam, covering the pivot pin of the R/H rear radius/trailing arm.
This shroud uses 14A7091 rubber plug not suppl...
Special shims for adjusting your swivel pins on the front hub. See workshop manual for correct settings - these are 005 thou but if you need 10 thou see 2A4241.
The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...
Floor pan front to rear for the left hand side, only to the floor shape before rod change cars - ideal for MK1/2 restoration.
For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.
Have you got one of the rare "wet" suspension Minis? This is the retainer plate that holds the protective sleeve around the hydro hose on the bulk head panel.
Sold singly 2 required per car.
Sold in pairs only.
These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable ...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.