USED MAINSHAFT EARLY 4 SYNCHRO 14MM NOSE

22G833MS

£85.00 exc vat

£102.00 inc vat

Out of stock

USED 4-synchromesh mainshaft for gearbox transmission with 14MM nose (13.97MM)0.550" required for either 1st motion shafts 22G1371 or 22G1093. This is Pre Aplus.

Reference=3 synchro mainshaft 22G392 is shorter and so is the 18mm nose late 4 sync mainshaft DAM7484

2G833 total length 26mm (10.24")

£85.00 exc vat

£102.00 inc vat

Out of stock

Alternative products

MAINSHAFT EARLY 4 SYNCHRO

22G833

4-synchromesh mainshaft for gearbox transmission with 14MM nose (13.97MM)0.550" required for either 1st motion shafts 22G1371 or 22G1093. This is Pre Aplus. See 22G833MS when no stock

Reference=3 sync...

£116.00 exc vat

£139.20 inc vat

People also bought products

2ND GEAR 4 SYNCHRO PRE A PLUS 26 TEETH

22G1094

Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...

£112.00 exc vat

£134.40 inc vat

PRE A+ 1ST MOTION NEEDLE ROLLER.

CHM172

This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.

This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...

£3.75 exc vat

£4.50 inc vat

BRONZE THRUST WASHER FOR PLANET WHEEL PRE A+

2A7062

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

£2.22 exc vat

£2.66 inc vat

LAYSHAFT 4 SYNC COMP HIGRADE ( PRE 3 STEP . PRE A ...

C-22A1738

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

£29.12 exc vat

£34.94 inc vat

BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO

BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

£0.45 exc vat

£0.54 inc vat

CROWNWHEEL + PINION 3.4 RATIO PRE A PLUS 22A411/41...

CWP3-4

Stronger PRE a PLUS with 62 tooth crownwheel plus the 18 tooth pinion making a 3.444 diff ratio as used on Cooper S, plus many 998cc cars from 1970 on.

£189.00 exc vat

£226.80 inc vat

COOPER S 4 SYNCHRO LAYGEAR

22G1040

"S" laygear. UK made for all pre-rod change. 4 synchro gears were the same except for the laygear and 1st motion shaft. The Cooper S and 1275GT had a closer ratio with a 18 teeth 1st motion and 29 teeth (15,20,25,29) 22G1040 laygear. The...

£227.20 exc vat

£272.64 inc vat

DIFF CROWNWHEEL LOCKTAB

ATA7385

All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly

£2.05 exc vat

£2.46 inc vat

DIFFERENTIAL FIBRE THRUST WASHER STANDARD SIZE

BTA101

Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...

£1.80 exc vat

£2.16 inc vat

DIFF CAGE ROLL PIN