FLYWHEEL KEYWAY LOCATING PLATE A+
DAM5923

£9.75 exc vat

£11.70 inc vat

In stockIn stock
The flywheel locking plate is for verto type flywheels only. For earlier pre vert types see 88G508

£9.75 exc vat

£11.70 inc vat

In stockIn stock

Recommended usage 1 x DAM5923 to fit one mini.
Verto Clutch & Slave Cylinder 1982 ON - Qty 1
Flywheel and Clutch - Qty 1

Recommended products

Flywheel bolt with built in locktab for Verto type flywheels (short lever clutch) only. Manufactured by a top bolting company correct to factory drawings. For Pre-verto clutch (long lever type) use 22A747 bolt with a 22A1155...

People also bought products

Verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Non Genuine three piece verto clutch kit, has a 180mm wide clutch plate, pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines. For Borg and Beck see GCK151MS

From 1990 on the...

Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up ...

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Verto 20% upgraded performance pressure plate which should be used with 190mm organic clutch plate C-AHT594 or the paddle type drive plate as used in racing C-AHT600. This pressure plate has a blue paint identifying mark and...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Upgraded Centre boss for all verto clutch/flywheel.

Fixing bolts are DAM5920 which are supplied in many clutch kits.

This is for single point injection cars. should be balanced with pressure plate.

This flywheel must use a VALEO PRESSURE COVER or Minispares C-AEG485 with 20% upgraded pressure or the car WILL NOT START because the timing slot w...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Performance type Verto 190mm wide paddle type drive plate as used for racing.

This will not fit pre Verto backplate/flywheel as it is to wide.

Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate

This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

Ring gear for all cars fitted with the pre-engaged starter on Verto flywheels from about 1984 on.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping

pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of G...