£1,146.05 exc vat
£1,375.26 inc vat
£1,146.05 exc vat
£1,375.26 inc vat
Recommended usage 1 x FZX3052 to fit one mini.
For 1-1/4" carb applications, this Conical K&N filter is the answer. Fits single or dual carb setups. Sold individually.
K&N airfilters are unsurpassed in performance yet are compact in size to fit in even the most cramped quarters.
Chrome pancake air filter for 1.25" SU. 5.5" diameter, offset mounting, 1" (+0.5" nuts) thick. Washable, reuseable filter element.
Many SU carb users (stock on all Spridgets) found their car equipped with pancake air cleaners. These have bee...
Cast alloy type,this intake manifold for twin 1.25"SUs (H2 or H4 -- NOT HS4)
It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places. Further blending ...
The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.
Accelerator bracket for twin carb models, mounts to inlet manifold.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...
This is the left hand linkage lever that sits on the rods between HS type twin carbs.sold individually
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Special clip for all our braided s/steel petrol hoses.14mm to 16mm.
This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
A special 3/8" unf half nut (9/16"AF spanner size)for fitting on rear brake hoses and carbs to manifold.
Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.
Bolt used in our anti roll bar kit and for holding plate on speedo drive housing on gearbox
Throttle return springs for all twin carb variants. Usually 3 fitted.
Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER
This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.
Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.
Gaskets and spindle/float lid seals for all the HIF38/44 range.
For HIF38 service kit see CSK94 for mini and CSK78 for metro
for HIF44 see CSK75[/lonk] except turbo
[link]CRK167 rebui...
Our heavy duty throttle cable is superior in many ways.
A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.
Cable to carb bolt is ACC5062.
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.
Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...