OIL FILTER HOUSING - PRE 1992
TAM2097

£12.80 exc vat

£15.36 inc vat

In stockIn stock
Filter housing for spin-on filter.

This housing uses a 1/4 npt taper thread union.

The later type (92onwards) 12A engine numbers has 11/16" thread size.

For performance use see 12A2032RACE.

£12.80 exc vat

£15.36 inc vat

In stockIn stock

Recommended usage 1 x TAM2097 to fit one mini.
Oil Filter Components - Qty 1
Oil Pumps, Filters and Coolers - Qty 1

Recommended products

3/8"unc 1.6250" long stud for engine block to accept the TAM2097 screw on filter head and for HS2 carbs, alternative to this is CHS2614 1.75" long and just over one thread longer. LYG10008 bolt was ...

Gasket for all spin on filter heads to block except aftermarket billet types which use 88G402. For the latest state of the art gasket material see GUG705553GM

Block to filter head gasket when spin on type filter is used (except billet types which use 88G402). The black side goes against the engine and the red against the filter. This also has a sealant strip on it to help stop leaks.

Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.

Same manufacturer and item as GFE443 but with our livery on so you know you are g...

Alternative products

Spin on oil filter housing for performance engines-uses 88G402 gasket-made out of billet alloy it has a strong mating face to the block where oil leakage occurs from high revving engine vibrations, is slightly shorter offering more clear...

Billet oil filter housing for engines with 12A prefix-Uses 88G402 gasket.

The original is no longer available but this is an upgraded version to stop flexing and cracking especially sort after by racers.

Should be used ...

Kit products

A kit to convert the early style cartridge oil filter to the later style spin on filter.

People also bought products

Crankshaft washers for crankshaft at 3 thou oversize on each one

sold as a set of four for 998 and 1100cc.

A kit to convert the early style cartridge oil filter to the later style spin on filter.

Victor Reinz large bore head gasket for A-series engines.

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

Genuine Mini Spares engine front plate for pre A+ plus timing gear.



this fits engines using the early egg shaped cover



This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersu...

AC Dodd Road Torque cam, great for low end power. Please see picture for full cam specs.



Road torque, this cam for strong low & mid range lugging, Touring, Smooth idle, excellent emmisions



ACD - RT

Power...

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

Spring seat shims (set of 4), 0.040" thick (1mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...

Steel ring set, 3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

This is the large seal for the early type oil filter assembly pre spin on type.

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

Replacement O ring for the Minispares range of chrome dipticks

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

Main bearings plus 60 oversize, 1275 2" mains. 60 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.



Sintered copp...