(¥0) £0.13 exc vat
(¥0) £0.16 inc vat
In stock
Following are oil pump bolt lengths.
GFK5170 is 1.5" long Holburn Eaton and Sureflow.
BH604131 is 1.6250".
BH604141 is 1.75" concentric.
(¥0) £0.13 exc vat
(¥0) £0.16 inc vat
In stockRecommended usage 4 x GFK5170 to fit one mini.
Specially designed for twin point injection cars. This kit has the 2 overiders and corner bars plus a stainless steel bumper with the pre stamped hole, plus fixings, for cars with 4 front driving lamps as fitted by Rover from 1997 on. Owing to the 4 ...
Car set of fixings to hold on the Deluxe type overiders and corner bars, complete with sealing rubber to bumper and spacers.
If you have standard overiders see kit MSSK011.
This kit has 2 special overiders and 2 slightly shorter corner bars
for fitting to cars with 4 driving lamps when fitted as original equipment by the factory on all Twin point injection cars. This special kit was designed by Keith Dodd for ...
The "Deluxe" models of all Minis included bumpers with these fancy over-riders and corner bars. This rear only kit is designed to provide you all the pieces; including, all the bits and the bumpers!
Includes bumper, the complete overrid...
Complete nut, bolt and washer set for engine to gearbox only
Engine mount bolt kit for manual cars, 1 kit requried per car.
5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap
Stainless steel version of GFK5184, worth keeping a few spare as they are one of the most common bolts fitted to the Mini.
Stainless steel version of GFK5185, worth keeping a few spare as they are one of the most common bolts fitted to the Mini.
Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.
Clutch housing bolt to engine long 5/16" UNC 1.75" long Fitted ffrom 1985 for clutch housing instead of 22A152 stud
Special thread cutting screw 1/4 UNF 1.25" (31mm) long.
Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
Self tap screw No10 for holding wiper motor strap to body and any other use.
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...
An aftermarket version of the mini bumper in stainless steel it has the original type open ends (Rover curled the sharp edges over) - BUMPER BOLTS ARE FITTED BUT NO NUTS -3 required metric M6 thread nuts FS106047
For top qualit...
Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.
Also the bolt to hold the starter motor.
Also the bolt for the [...
Front subframe to front teardrop mounting, clutch case to block.
Engine mounting to subframe - easier to use than the GFK5184 - 3/4" long
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.