(¥58) £57.65 exc vat
(¥69) £69.18 inc vat
In stock
(¥58) £57.65 exc vat
(¥69) £69.18 inc vat
In stockRecommended usage 1 x GS15398 to fit one mini.
Genuine Mini Spares product.Quarter window seals for non-piano hinge type pop out rear side windows as fitted to Mk3.
Plenty of imported copies on the market but this is our true UK copy of the original as made by Standard Products for Rove...
The plastic chrome insert for fitting in the windscreen and backlight rubbers of all minis. You will require TOOL02 to fit these.
Genuine Mini Spares quality product. For Mk1 cars use 14A8744
For Pickups you will need to cut and shorten either seal and make sure the join is at the bottom. The extrusion is the correct shape.
This seal is the best ...
Genuine correct length with cut outs and drain holes in the correct places.
The MK3 door seal is notable because of it's large 'bulb' area. The 'bulb' is the round section that the door closes against. The size is determined by how much gap ...
Rubber seal for all mini windshields. Uses locking strip 24A1466(chrome) or 37H8052(black.) REMEMBER YOU MUST FIT THE RUBBER TO THE BODY FIRST. DO NOT USE THE STRING METHOD BECAUSE IT STRETCHES AND TEARS THE RUBBER.
There is a later wider r...
Boot hinge gaskets and fittings for original type hinges
Introducing the Classic Mini CST Rear Tow Eye, a tough hook which is laser cut from 5mm thick 304 stainless steel and then coated with a slight chrome finish. This means it’s not only strong and durable but also sleek and precise.
...
High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!
Captive nut plate that sits behind the damper bracket on the inner wing/bulkhead to attach the damper brackets. 2 PER SIDE.
The gasket that sits behind the door stiker on all wind up window type minis
on the B post.
MK3 Door & boot handle fitting kit, including original type screws, star washers and gaskets.
Metal floor plug as per original with rubber seal.
For use in 1" hole.
Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.
Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
MK3 Black Mini door and rear quarter trim(4 piece kit) in vinyl as per original twin line pattern per Mini and CooperS but for cars after May 1973 where the rear quarter panel trim shape did not have a cut out for the ash tray mount and if you look a...
Protective wax Rover introduced to protect newly drilled holes in bodywork for such things as Badges. A small 10ml sachet only but ideal for any new holes drilled for wiring,screws and badges where metal could be left bare.
Thses were suppli...
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Van R/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length -plain pressed floor with indents but no carpet brackets or lugs underneath.
Van L/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length-plain pressed floor with indents but no carpet brackets or lugs underneath
non genuine L/H outer MK3 door skin lower few inches repair section.
not as good a fit or looking as the genuine complete skinCZH3301
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.