LATE COMPETITION DRIVESHAFTS (TARMAC) - POT JOINT ...
C-BTA1264

($209.25) £209.25 exc vat

($251.10) £251.10 inc vat

In stockIn stock
Competition driveshafts made in steel for use with inboard pot joints.

Upgraded to stop ends twisting off. For Hardy Spicer type see C-BTA1265. Circlips not included. 37H8706 is the inner circlip and ensure it fully engages shaft and joint.

($209.25) £209.25 exc vat

($251.10) £251.10 inc vat

In stockIn stock

Recommended usage 1 x C-BTA1264 to fit one mini.

People also bought products

Non genuine aftermarket only as the genuine originals are obsolete.

These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...

Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.

these...

These shafts have changed diameter thickness over the years but these are the

original thick type and upgraded to EN24 for competition or standard uses.

this is the left hand short one.

These shafts have changed diameter thickness over the years but these are the

original thick type and upgraded to EN24 for competition or standard uses.

this is the right hand longer one.

In board CV joint(pot joint) gaiter kit with plastic clips and grease.

Non Genuine item many sell as GSV1073.

The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...

Hardy-Spicer coupling was fitted to the Cooper "S" and all automatic varieties pre Pot joint(inboard cv joint) This U-joint assembly slides onto the driveshaft and bolts to the Cooper S output shaft flange. The U joint fitted to these joints is the s...

Special grease for Cv joints and any homokinetic joints. Enough for one joint only.

Steel driveshafts with original circlip holes, ensure that the cv circlip clicks fully in both shaft and cv joint.

These are upgraded to stop the ends twisting off. Available for rod change also as C-BTA1264 SOLD AS A PAIR

One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...

Genuine Rover Xparts item. See BHM7012 which many vendors sell as their GSV1073.

In board CV joint(pot joint)gaiter kit metal clips and grease.

The single largest reason for the failure of this rugged assembly is contam...

Thin driveshaft circlip for outer c.v joints.

Also replaced 22G2688 for the inner pot joint circlip. Not required for hardy spicers or rubber cross type inners couplings. Sold singly 2 required per car.

Outputs for LSD when using inboard CV joints. Sold single with 2 needed per car.

Original 17H8597 became NLA from Rover december 2003 as a spare part but this circlip was used to build up the last Rover hub assemblies previous to then.

We have found these clips work fine on standard road use

For all rod change gearbox mechanism housings, this as un uprated poly bush replacement for the standard rubber bonded mount

The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!

The Swiftune Quaife ATB avoids the need fo...

Kit which enables you to fit a rod change gearbox to an earlier round tunnel.

Competition crownwheel bolt for use with our LSD crownwheels, these are CNC machined from EN24T with a reduced head height for more gearbox clearance.

Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS

Using only the original manufacturers of the bearings such as RHP because all t...

Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...

Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.