CLUTCH SEAL PROTECTOR SHIELD-FITTED TO VERTO CLUTC...
DAM2821

($3.00) £3.00 exc vat

($3.60) £3.60 inc vat

In stockIn stock
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when stripped down as they get brittle.

($3.00) £3.00 exc vat

($3.60) £3.60 inc vat

In stockIn stock

Recommended usage 1 x DAM2821 to fit one mini.
A Plus Blocks 1275 Engines with 12H Engine No - Qty 1
Verto Clutch & Slave Cylinder 1982 ON - Qty 1
Primary Gear Train - Qty 1

Recommended products

See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.

This ...

Genuine Mini Spares product in Viton.This oil seal was introduced in 1991 with the first injection models and the HIF38 carb version cars and has the internal spring closer to the back. Meant to help with extra crankcase pressures and nips up slightl...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

People also bought products

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Non Genuine three piece verto clutch kit, has a 180mm wide clutch plate, pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines. For Borg and Beck see GCK151MS

From 1990 on the...

Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up ...

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Verto 20% upgraded performance pressure plate which should be used with 190mm organic clutch plate C-AHT594 or the paddle type drive plate as used in racing C-AHT600. This pressure plate has a blue paint identifying mark and...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Upgraded Centre boss for all verto clutch/flywheel.

Fixing bolts are DAM5920 which are supplied in many clutch kits.

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Performance type Verto 190mm wide paddle type drive plate as used for racing.

This will not fit pre Verto backplate/flywheel as it is to wide.

Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate

This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

Ring gear for all cars fitted with the pre-engaged starter on Verto flywheels from about 1984 on.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping

pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of G...

Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use [link]...