£16.75 exc vat
£20.10 inc vat
Out of stock
You need to purchase a new seal, see AAU2304.
The gasket for this is GUG705565GM.
The retaining stiffener clip is 22A862.
Remenber-these are anywhere from about 25-50 years old.New one are not available
£16.75 exc vat
£20.10 inc vat
Out of stock
Follow your speedo cable to the gearbox and it screws onto an alloy housing bolted to the gearbox. This is the gasket between the housing and the gearbox.
:USED: Speedo cable drive pinion in the gearbox with 17 teeth, it was used with a 6 tooth drive spindle on all 10" wheel cars pre 1980.
Either brown or plain white sort of colour about 20.50mm to 21.12mm in diameter and very similar to [lin...
USED 6 teeth speedo drive spindle that mated with 17 tooth speed pinion 22A1881 on cars with 10" wheels before 1980 plus any year 1275GT. Also 12"wheel cars with 3.44 final drive 1984 on. On the Metro mini this was used with 17 and 18 te...
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.
Also the bolt to hold the starter motor.
Also the bolt for the [...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.
The metal retainer that holds the rod change gear lever gaiter CZH4278 in place
Two of these long UNC bolts are required to hold the alloy remote control to the gearbox diff housing on Remote type gearboxes. The two short UNC bolts are GFK5240.
Genuine gearbox gasket for the large alloy end cover which also houses the speedo drive pinion for all years of mini. The small gasket on the alloy housing with 2 bolt holes is GUG705564GM and the small pear shaped speedo housing gasket ...
USED ITEM-The clip to retain the DAM8488 the alloy housing that the speedo cable attaches to and often leaks oil.
The gasket for the housing is GUG705565GM
Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.
Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.
The 6 longer ones are 22A152.
These st...
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.