£46.50 exc vat
£55.80 inc vat
In stock
Replaces the ori...
£46.50 exc vat
£55.80 inc vat
In stockRecommended usage 1 x GXE2211 to fit one mini.
High output, uprated to 70amp (from 45 and 55amp) alternator as used on 89 on model Minis.
Will fit most Minis from 1980 until 1996, except some aircon models (requires transfering the old twin belt pulley to new alternator - see ...
Identical to the GXE1002 competition alternator but with a larger pulley designed to stop over charging the alternator on race cars which spend the majority of time at high rpm. Weight 3.277 kg.
Lightweight competition alternator for all pre 1997 mini's. This unit weighs 3.2kgs and outputs 55 amps. Designed as a direct bolt on replacement but features a multi position mounting bracket so ideal for race cars/custom applications also. Does not...
This lightweight alternator is favoured by competition users, new design for 2014 these are now a direct replacement for the original alternator so no additional brackets are required. A small amount of wiring required to fit the Mini wiring loom.
This is the plug that fits all Mini alternators, except MPI. The three conections are alternator output, 12 volt sense and ignition lamp. Ideal when converting from a dynamo.
This very trick pulley is machined from billet aluminum & black anodized. It is oversized (5") to reduce the speed of the generator or alternator on high rpm engines preventing over charging the system.
When using this pulley with the origi...
Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo
Alternator bracket fitted on the block of earlier Pre A series engine blocks.
For later A plus blocks see CAM4853
High output, uprated to 70amp (from 45 and 55amp) alternator as used on 89 on model Minis.
Will fit most Minis from 1980 until 1996, except some aircon models (requires transfering the old twin belt pulley to new alternator - see ...
Alternator bracket for A Plus engines and Pre A+ engines with dynamo fitted. See 12G1053 for earlier Pre A plus alternator bracket.
Fitted from 1996 only this alternator sits higher than originally, with new brackets that will only fit the twin point injection cyl head. A1151-65 type producing 65amps (Was GXE2862 from Unipart). If your battery seems to be always running low it mi...
LARGE ALLOY HEAVY DUTY ALTERNATOR BRACKET FOR ALL PRE A PLUS ENGINES(PRE 1980) AS USED ON ABINGDON ST WORKS CARS
The adjusting link bracket for dynamo and alternator that fits on the 12G289 pillar.
Starter solenoid bracket that bolts to the flywheel housing on MK1/2 cars. For Cooper S see 12A326.
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Wiper motor kit for all mk2 onwards cars, includes wiper motor, motor gear, wheel boxes, outer tube kit, wiper rack and wiper motor ferrule.
Clip to retain the speedo cable to the bulkhead on pre 82 cars approx. This clip is also used to hold the loom to the inner wing on some cars.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
Interior lamp with a black on/off switch and pointed torpedo ends.
Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.
Also there was an alternative lamp with black switch and square ends 13H192 which w...
This is an ultra reliable universal hazard light module kit for any Mini that did not have hazard lights as standard (pre 76 cars).
A discreet but important safety upgrade for all classic vehicles.
Should you ne...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.