R/H rear lower genuine corner section of the rear valance on vans.estates.travellers and pick ups
Minis most used rubber plug 1.25" wide for holes approximately 7/8".
Fits floor, aerial hole and steering column extra hole and radius arm shroud on MK1/2 minis.These floor plugs vary in number from 11 in a Elf/Hornet,Mk1 and 1994 on cars do...
complete tailgate for the mini pick up from genuine tooling but less the hinges
genuine panel that holds the headlamp assembly on the mini clubman versions.
this is the right hand side
this non genuine panel has all the fitting holes and metric M6 castellated nuts for the rear fog lamps which were fitted as standard from 1983 on. The M6 bolts required are 10mm long and DYP10002 can be used. The wiring grommet for this ...
The lower metal front dash panel that you would actually put your stuff on and is usually covered by vinyl cloth or cardboard.
This panel is NOT now a complete solid type panel as per early cars and now looks like a fabricated piece of metal...
rear fog lamp bracket which attaches to the rear valance -right hand drive only.
If you have fitted the old type overiders and corner bars for the Retro look you will need to fit a modified bracket MSS024 which is basically the left hand dri...
The section forward from the damper (shock absorber) bracket area
these sections approx 20" long often rust around the areas where they weld to the front wings.
This is a genuine half panel of the HMP441008-26"long for the right hand side
with fixings for the subframe mounts.
Non genuine MS51R section repair panels are only 11" long
Although used on vans with metal loa...
This panel is for wind up window type doors that have internal hinges and this contains the part of the front A post where the hinge and door stay holes are down to and including the door step and along and up the B post a few inches covering the mai...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping.
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping.
Fits all minis with side repeater lamp from 1988 up until 1996 except export models with adjusting headlamps.
1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusting motor. cars registered after 1st...
This R/H sill(rocker)panel has the correct 4 pressed vent hole shapes, but is of a revised design supplied by Rover where the vents lay slightly further back into the body. But we suggest you fit MS30R the correct shape 4" Non Genuine p...
Fits all minis with side repeater lamps and an aerial hole from 1988 until 1996 except export models with adjusting headlamps. After 1997 ASB360010 should be used, which has no aerial hole, and a recess for the dipping headlight motor. ...
This is the Left hand rear panel see HMP441011 and also 14A9558/9 complete arch.
The oversill panel includes the horizontal external seam and wraps all the way down with a lip that meets the horizontal part of the floor. 4 flute type as per pre 1970 cars but for 6 flutes see MS55R
2-3" lower section of Van body section
from A post to rear wheel arch including the vital door step sill profile that rusts plus the horizontal edge that the chrome trim sits on-for cars with hinge tye doors
The oversill panel includes the horizontal external seam and wraps all the way down with a lip that meets the horizontal part of the floor.
This is the 6 vent style which started on Mk3 minis late 1970 on. Most 1970 including all Cooper S M...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.