($118.50) £118.50 exc vat
($142.20) £142.20 inc vat
In stock
See our accessory catalogue for picture guide if you are not sure for other applications.
For pre '64 cars see 17H5019.
($118.50) £118.50 exc vat
($142.20) £142.20 inc vat
In stockRecommended usage 1 x 17H8608 to fit one mini.
Without doubt the best hose to fit unles you are after the lovely silicon
extra strong and supple hoses. See GRH1006 for lengths required if you are not sure on your car.
The heater is not available anymore, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air.
This fits the early Mk1 cars only with 5" gap between pipe hole centres, after 1963 17H8608
Universal aluminium heater assembly complete with heater matrix and electric fan. Comes with 2 outlets for demisting windscreen and 2 variable vents for heating the rest of the car. Ideal for track/race cars or simply for those who want to replace th...
Heater Matrix take off fixing kit, cars only-fits on heater matrix to take the 2 heater pipes on L/H side of car.
kit includes 2 brass take off pipes with 2 stainless steel bases and 2 water seals.
The outlet pipes are made in brass...
2 plastic 5/8" outlets at the same end and close together which exit the heater on the r/h side. The later HIF38 1275 and single point cars had a change point where the plastic outlets exited on the l/h. This is a JEF10005.
These units take ...
The heart of your heater is the radiator matrix which often gets overlooked when cleaning the cooling system. They often get clogged and cannot be cleaned rendering your heater useless. Replacement is the only answer if flushing out does not clean it...
The heater outlets exit on L/H and are horizontal for 5/8"hose fitting.
The outlets for this mod come seperately, as part number JEP10008.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
As fitted to MKI minis and variants. Original style tube of rubber material wrapped over a wire coil. As an improvement to the original design, these are also bonded to a nylon interior membrane for additional strength and the wire coil is galvenised...
Heater vent demister covers for the pre 1969 heater assembly.
Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
Genuine Mini Spares heater valve. The original RANCO tooling has been scrappped so beware of some imports available where the inners quickly explode loosing the metal cap and all your water when operated.This has M4 metric thread bolt included for th...
Heater to in line heater valve -this hose is 8" to short bend-long part is about 14.5" and the short bend is 2.25" long. 25"total length if using GRH905. ($26.99) £26.99 exc vat ($32.39) £32.39 inc vat
Used with BAU5043 heater and 5/8"hose pre1991. This hose fits
Fitted from approx 1969 to 1988 they replaced the original knob with the word PUSH and HEATER. This was done as a safety feature by having a rubber edge. The grommet in the body for this cable to pass through is CAM5969. Cable length is ...
from air vent on dash to duct-about 5"(128.9mm)long with 2.5" diameter
This gasket fits on the cylinder head for every A series heater valve or outlet pipe until the hole was no longer drilled when they changed to a heater valve fitted into the hose line from 1990 on.
Heater valve studs fitted to the cylinder head. 1/4"unf 1.1250" long.
Stainless steel heater tap studs for the cylinder head.
Twin point Mini heater tap that fits to the heater assembly
Heater hoses and expansion tank hoses are mostly 5/8" from 1985 on so check the bore size as some were actually 1/2" hose with flared ends of 5/8" you will need to use a restrictor pipe MOC210.
Original 5/8" rover hoses were 1"(...
