AMAL CARBS ONLY SET OF 4 (ARDEN EIGHT-PORT)

Set of four amal carbs as originally used on the works minis with 8 port cylinder head--3 have a double banjo on the bottom for fuel and one with a single banjo for the end fitting. See C-AJJ4083 and C-AJJ4064

($873.65) £873.65 exc vat

($1,048.38) £1.048.38 inc vat

8 PORT FUEL INJECTION KIT

C-AJJ4065

Brand new fully programmable injection kit for the 8 port head contains-

ECU and bespoke loom, crank sensor and mounting kit, air and water temp senders ,air filter and base, high pressure fuel pump, fuel filter and a regualtor,

thr...

($2,900.00) £2.900.00 exc vat

($3,480.00) £3.480.00 inc vat

CARB RUBBER GASKET (ARDEN 8 PORT)

C-AHT531

fit amal carburettor on 8 port cylinder head

($9.00) £9.00 exc vat

($10.80) £10.80 inc vat

THROTTLE ACTUATING ROD (ARDEN EIGHT-PORT)

DR007

,

($18.75) £18.75 exc vat

($22.50) £22.50 inc vat

THROTLE LEVER ARMS (ARDEN EIGHT-PORT)

DR010

($8.40) £8.40 exc vat

($10.08) £10.08 inc vat

MALE ROD END ROSEJOINT 5/16" X 5/16" UNF

RM5U

These spherical rod ends are also known as a Rose joint which is a registered trade mark. We use these ends on some of our weber carb linkage kits and anti roll bars. This is the male type threaded joint.

($8.54) £8.54 exc vat

($10.25) £10.25 inc vat

AMAL CARBS ONLY SET OF 4 (ARDEN EIGHT-PORT)

C-AHT520

Set of four amal carbs as originally used on the works minis with 8 port cylinder head--3 have a double banjo on the bottom for fuel and one with a single banjo for the end fitting. See C-AJJ4083 and C-AJJ4064

($873.65) £873.65 exc vat

($1,048.38) £1.048.38 inc vat

8-P0RT INLET MANIFOLD GASKET

C-AHT379

Intake manifold gasket for Arden 8 port head.

4 required.

($0.65) £0.65 exc vat

($0.78) £0.78 inc vat

THROTTLE LINKAGE SUPPORT BRACKET (ARDEN EIGHT-PORT...

DR005

($30.56) £30.56 exc vat

($36.67) £36.67 inc vat

CARBURETTOR LEVER PIN

ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

($2.93) £2.93 exc vat

($3.52) £3.52 inc vat

THROTTLE CABLE ABUTMENT PEDESTAL (ARDEN EIGHT-PORT...

DR003

($11.40) £11.40 exc vat

($13.68) £13.68 inc vat

THROTLE CABLE LEVER BAR ASSY. (ARDEN EIGHT-PORT)

DR004

($40.00) £40.00 exc vat

($48.00) £48.00 inc vat

CHOKE CABLE TRUNNION ACH9042 NIPPLE & 53K3503 SCRE...

AUE34

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

($2.03) £2.03 exc vat

($2.44) £2.44 inc vat

NUT PLAIN 5/16" UNF

GFK3212

Zinc plated 5/16" UNF plain nut

($0.09) £0.09 exc vat

($0.11) £0.11 inc vat

NUT NYLOC 5/16" UNF

GFK3322

Zinc Plated 5/16" UNF Nyloc nut.

($0.14) £0.14 exc vat

($0.17) £0.17 inc vat

STUD FOR THERMOSTAT HOUSING WITHOUT SANDWICH PLATE...

CHS2515

Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...

($0.65) £0.65 exc vat

($0.78) £0.78 inc vat

CLUTCH CASE STUD SHORT 3 REQUIRED

53K547

Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.

The 6 longer ones are 22A152.

These st...

($0.59) £0.59 exc vat

($0.71) £0.71 inc vat

THROTTLE CABLES - CARB TO LEVER (ARDEN EIGHT-PORT)

DR009

($6.90) £6.90 exc vat

($8.28) £8.28 inc vat

LOCATING COLLAR (ARDEN EIGHT-PORT)

DR008

($5.63) £5.63 exc vat

($6.76) £6.76 inc vat

THROTTLE CABLE ABUTMENT BAR ASS. (ARDEN EIGHT-PORT...

DR002

($42.00) £42.00 exc vat

($50.40) £50.40 inc vat

AMAL INLET MANIFOLD EACH

C-AHT521

4 of these are used on an 8 port head set up and these are copies of the original works type in alloy casting.

($43.50) £43.50 exc vat

($52.20) £52.20 inc vat

WASHER PLAIN 5/16"

GFK1114

5/16" flat plain washer.

($0.06) £0.06 exc vat

($0.07) £0.07 inc vat

BOLT 5/16" X 1" UNC SETSCREW

GFK5234

Bolt for CHM85 differential side cover. 1" long UNC useful for pre verto slave cylinder and starter bolt. Also 12A361 engine mounting bracket to alloy case.

($0.17) £0.17 exc vat

($0.20) £0.20 inc vat

CYLINDER HEAD 8 PORT ARDEN LARGE VALVE PLUS PUSH R...

C-AJJ4064RACE

The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series has now been revamped and made available with larger inlet valves and special seats available to special order.Ports and combustion chamber...

($2,519.12) £2.519.12 exc vat

($3,022.94) £3.022.94 inc vat

8 PORT HEAD STUD AND NUT SET (STUDS EN24 CHROME MO...

C-AHT282

EN24 Nickel Chrome moly steel studs,Competition head stud kit.

torque to 45ftlbs -no need to re-torque cometic type head gaskets.

For use on the 2012 onwards heads only.

($58.76) £58.76 exc vat

($70.51) £70.51 inc vat

CARBURETTOR WEBER 45DCOE

C-AHT143

Genuine Weber 45DCOE Carb, calibration from the factory is as below:

Choke 36

Throttle Plate Angle 78 degrees

Auxiliary Venturi 4.5

Needle Valve 200

Main Jet 145 Pump Jet 45...

($532.50) £532.50 exc vat

($639.00) £639.00 inc vat

AMAL CARBS ONLY SET OF 4 (ARDEN EIGHT-PORT)

C-AHT520

Set of four amal carbs as originally used on the works minis with 8 port cylinder head--3 have a double banjo on the bottom for fuel and one with a single banjo for the end fitting. See C-AJJ4083 and C-AJJ4064

($873.65) £873.65 exc vat

($1,048.38) £1.048.38 inc vat

ROCKER ASSEMBLY ROLLER TIP / 8 PORT ONLY 2012on 6L...

C-AHT448

Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc 8 port cylinder heads only.

this kit has 6 L/H rockers and 2 R/H. Specially designed to fit the currecnt July 2012 on head, with corrected geometry to give more stability over the valve and...

($263.24) £263.24 exc vat

($315.89) £315.89 inc vat

CYLINDER HEAD HEATER TAKE OFF OUTLET 5/8"

12G2534

Once the old type alloy heater valve on the head was discontinued in 1990 for the plastic free floating inline type this take off union was fitted in its place on A series engine cars for use with the larger 5/8" hose. Uses 88G221 gasket...

($7.20) £7.20 exc vat

($8.64) £8.64 inc vat

PISTON. SINGLE 998 FLAT TOP LATE TYPE 10.3 TO 1 /

P22463-20

These are suitable for press fit gudgeon pin late type 998 con rods.

sold individually with rings and pin complete

Ringsets are available as R43240-20

($37.50) £37.50 exc vat

($45.00) £45.00 inc vat