($7.04) £7.04 exc vat
($8.45) £8.45 inc vat
($7.04) £7.04 exc vat
($8.45) £8.45 inc vat
Recommended usage 1 x FAM2807 to fit one mini.
Hose clip for FAM2807 hose between oil pipes on central speed mini clusters
Oil pipe in plastic 5 feet long, if fitting to a Tim gauge you will require LMA017 adaptor for the gauge.
Not comppatable with the CAM6431 standard oli pressure block union, and OA shoudl be purchased to fit.
With this large diameter line to the oil pressure guage you can actually see minor fluctuations in the pressure at idle or when the relief valve bounces open and closed. Because the braided steel line is one piece from the block to the gauge there is...
A kit to convert the early style cartridge oil filter to the later style spin on filter.
Engine mount bolt kit for manual cars, 1 kit requried per car.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.
Also available is a flanged nut C-AHT449
This is the large seal for the early type oil filter assembly pre spin on type.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Stabiliser bush kit for lower engine steady
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
UK made-EN24T allen key head extra strong 5/16"unf rocker adjusting screw, original screws are often worn but rarely inspected, both ends of this complex screw are often worn and in dire need of replacement. Most available on the market are imported ...
For our new drop gears where the front bush is held in by a circlip. Not for A Plus OR old straight cut type (this is NOT the top hat type rear bush).
19.85mm long- For use on the stepped type 1275cc type cranks this bush is fully floating a...
For those very early 25D type distributors.Mini Spares version for modern fuels as fitted to our distributor range with slide on vaccum hose inlet pipe-not the very first screw in type
For modern day petrol, except 1275cc. See 37H8379MS for 1275cc.
After lengthy tests we have found nearly all vac units are not to the originals but with the change of added oxygenates to petrol in the 1980's and then ethanol in ...
best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.
this is good for any head where a lot has been machined off-flat top pistons.
Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc big bore engines only.
Craddle type with larger upgraded shaft size to improve rigidity.
Ensure tightening down all posts equally to eliminate stress fractures on shaft.
24 teeth primary gear for all pre A plus 1275 engines with a floating bush fitting to suit stepped crankshaft.
Uses a floating bush with a circlip to hold it in place. This primary gear is suitable to use along with Standard pre a...