(250,00 €) £250.00 exc vat
(300,00 €) £300.00 inc vat
now
(230,00 €) £230.00 exc vat
(276,00 €) £276.00 inc vat
(250,00 €) £250.00 exc vat
(300,00 €) £300.00 inc vat
now
(230,00 €) £230.00 exc vat
(276,00 €) £276.00 inc vat
Recommended usage 1 x 21A291 to fit one mini.
SCREW, 1.25" long for securing 21A291 van petrol tank.
Large headed screw for safety. Short for securing the van petrol tank 21A291.3/4" long
Petrol tank pipe. This is the short metal pipe with a union fitted for vans/estates/pickups with an electric pump fitted. See 21A308 for mechanical pump which has a long pipe.
Metal petrol pipe with tank union, this is for all estate and van versions with a mechanical pump where a long full length pipe is required. Made in non rust
metal.
Replacement screws and nylon inserts for the Van, Estate and Pick up petrol tanks.
Stainless steel Non Genuine reproduction tank is in automotive stainless steel and fits all the long wheel base Minis, except for the very early side-tank travellers. Also used on many kit cars and specials owing to its shape.
Because of the...
Non Genuine reproduction tank fits all the long wheel base Minis, except for the very early side-tank travellers. Also used on many kit cars and specials owing to its shape.
Because of the outside location of these tanks, the originals seem ...
Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Non-genuine version of the choke cable fitted to the early minis which does
not lock into place like the twin carb version. (see 21A1204).
It was made to work with the single HS2 carb and had only the word "CH...
Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
Van R/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length -plain pressed floor with indents but no carpet brackets or lugs underneath.
Van L/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length-plain pressed floor with indents but no carpet brackets or lugs underneath
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Good quality pressing rear upper side panel,used for converting clubman estates to van sides or repairing van upper section back to original when windows have been fitted. This is L/H side.
Good quality pressing rear upper side panel,used for converting clubman estates to van sides or repairing van upper section back to original when windows have been fitted. This is RH side.
For MPI only when bonnet hook has been moved to central position.
This plate protects the bonnet lander panel from the hook and acts as a stiffener also. Stainless steel version.
This is the guide plate for the bonnet locking pin, now in stainless steel.
This is the Clevis pin for the hook part with a spring and spacer only. This fits all Minis and Clubmans as the bracket it attaches to is on all bonnets unless broken. The spring loaded catch is designed to keep the bonnet from blowing open while dri...
Curley fibre glass Mini Miglia wheel arches, approximately 4.8." wide, with front edge 6.9" at widest point. Requires MS127FK brackets. Probably the largest wheel arches used on minis. Please note these are white gel coat not black and w...
Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
Replacement screws and nylon inserts for the Van, Estate and Pick up petrol tanks.