(4,20 €) £4.20 exc vat
(5,04 €) £5.04 inc vat
In stock
(4,20 €) £4.20 exc vat
(5,04 €) £5.04 inc vat
In stockRecommended usage 1 x 22A419 to fit one mini.
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
Oil seal for speedo drive pinion cover (DAM8488)
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
The new improved KAD quickshift is a redesign of the original KAD stick incorporating many detail changes.
* Reverse is now selected by lifting a collar beneath the gear knob.
* Now supplied with an alloy gear knob.
...
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.
Also the bolt to hold the starter motor.
Also the bolt for the [...
The gasket with the oil suction seal hole fits every mini gearbox case and the other two are for the different case shapes, one for 3 synchro case and one for 4 synchro gearbox case, so choose the one you require. For latest spec Klinger gasket set u...
Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.