(152,00 €) £152.00 exc vat
(182,40 €) £182.40 inc vat
In stock
(152,00 €) £152.00 exc vat
(182,40 €) £182.40 inc vat
In stockRecommended usage 1 x ADU3490-60 to fit one mini.
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
Made in a hyper eutectic alloy with a high silicon content to provide tight cylinder clearances and quiet running characteristics, manufactured by a world class piston manufacturers specification" uses an optimised crown and dish (9cc) shape for impr...
60 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some Metro versions it was higher.
Current pistons ...
Available at the moment but they sporadically become unavailable. Mini Spares have also had a batch of plus 60s specially commissioned to us for Grass trackers and racers. sold individually with rings and pin complete.
Ringsets are availabl...
0.625"(1.59mm)compression ring and 1/8"(3.175mm) single one piece oil control ring.
Also available is a high grade ring set C-STN99-40 with 3 piece oil ringfor these pre 1979 type pistons
These Piston rings are +40 oversize with 0.59" compression rings and 0.1181" oil ring fo 998cc
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...
3 OF 0.625 COMPRESSION RINGS AND .1575 OIL CONTROL RING.AT PLUS 60 OVERSIZE
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Race quality heavy duty double row performance endless timing chain. It is the best chain available and used by top engine builders, also fits MGB/Midget. This chain is for duplex gears that is used by racers as a limited stretch heavy duty version m...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.