(246,41 €) £246.41 exc vat
(295,69 €) £295.69 inc vat
In stock
(246,41 €) £246.41 exc vat
(295,69 €) £295.69 inc vat
In stockRecommended usage 1 x C-STN22 to fit one mini.
Replace these nuts when you remove your exhaust from the manifold downpipe and check the studs TD108051A also as they all seem to corrode or wear. Metric M8. These nuts should be replaced as they have a crimped thread to lock on the stud...
2 reqd but sold seperately-From 1990 rover started fitting the hanging rubber exhaust mounting straps which push onto rods on the exhaust and rear subframe similar to the old metro. These were used right to the end of production on minis.
Downpipes to fit onto the original exhaust manifold when retaining the catalyst on fuel injected late Coopers. Manual cars only
Special length and thread pattern only for the exhaust manifold to downpipe of injection cars, see also FX108047 special nuts. Metric M8.
Metal gasket for the catalyst and is the same both ends for Cooper 1275CC RSP early cars, but only fitted on the front to later cars. If you cannot fit this gasket on the rear your car does not need one.
Just what injection engines require, this element will increase the breathing
to the engine which can only result in better performance all round. Once fitted these special elements can last nearly a life time if cleaned and oiled regularly ...
Rear RC-40 fitted with a pipe to bolt straight on to the catalyst for cars built late 1991 onwards (not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a single box system with a little throat...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
Part of our millennium range of exhausts, this is the 200 Cell sport cat.
Catalytic converter will fit all mini models and if you require new studs the part number is FB110351 and the nuts to fit the studs are NV110051<...
THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines with HS4 carb. Gives 20% more power and 12% more torque.
Using all the top quality tried and tested parts the Kit includes
RC40 twin box [link]RC...
Stabiliser bush kit for lower engine steady
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares fitted one on their 1380cc engine road car in August 2014 with great results. Rarely you may require longer rocker...
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
Billet oil filter housing for engines with 12A prefix-Uses 88G402 gasket.
The original is no longer available but this is an upgraded version to stop flexing and cracking especially sort after by racers.
Should be used ...
"Green Engine Paint", maintenance can mean more than mechanical. Even if you don't rebuild it, painting it can at least make it look new! And if you actually are rebuilding the motor, you are sure to want to make sure everyone knows! It's Easy! Sup...
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
THE M10 METRIC bolt 25mm long for holding alternator plus other parts on the Twin point minis
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.