CLUTCH ARM CLEVIS PIN BOTTOM
CLZ628

£1.45 exc vat

£1.74 inc vat

In stockIn stock
The large clevis pin that goes through the clutch lever arm at the bottom of all minis.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 most mini clevis pins except CLZ409

GHF510 for GCV1105 CV joint and rear hub nut

GHF511 for GCV1013 CV joint

£1.45 exc vat

£1.74 inc vat

In stockIn stock

Recommended usage 1 x CLZ628 to fit one mini.
Clutch Housing - Qty 1
Flywheel and Clutch - Qty 1

Recommended products

Upper clutch lever arms clevis pin, suitable for both verto and non verto arms.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 mos...

Universal split pin for all mini clevis pins, except handbrake lever.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 most mini cle...

Alternative products

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Kit products

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

People also bought products

Verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Non Genuine three piece verto clutch kit, has a 180mm wide clutch plate, pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines. For Borg and Beck see GCK151MS

From 1990 on the...

Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up ...

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Verto 20% upgraded performance pressure plate which should be used with 190mm organic clutch plate C-AHT594 or the paddle type drive plate as used in racing C-AHT600. This pressure plate has a blue paint identifying mark and...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Pre verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Upgraded Centre boss for all verto clutch/flywheel.

Fixing bolts are DAM5920 which are supplied in many clutch kits.

Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof wa...

Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.



small face with numbers stamp-face outwards, larger surface aera side face flywheel.

3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.

Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Performance type Verto 190mm wide paddle type drive plate as used for racing.

This will not fit pre Verto backplate/flywheel as it is to wide.

Performance type Verto 180mm wide paddle type drive plate as used for racing.

Alternative to AP Racing plate