NUT NYLOC 5/16" UNF
GFK3322

£0.14 exc vat

£0.17 inc vat

In stockIn stock
Zinc Plated 5/16" UNF Nyloc nut.

£0.14 exc vat

£0.17 inc vat

In stockIn stock

Recommended usage 1 x GFK3322 to fit one mini.
Clutch & Pedal Linkage - Qty 1
Steering Rack - Qty 4
Rear Suspension, Hydrolastic - Qty 2
Steering racks - Qty 4
Brake/Clutch Pedals and Controls - Qty 1
Rear Subframe - Qty 4

Recommended products
Kit products

Every nut, washer, bolt, rubber bush and 2 pins that hold the rubber bushes that are prone to rusting badly and are required every time you do a subframe change. Including the 2 large penny washers this kit has 36 components. Other companies offer l...

Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.

complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43

Rubber mounts are made in the UK.

Heavy duty needle roller type coupling with plastic ends. The very early Minis used the rubber joint drive couplings GCD101 to eliminate harshness from being transmitted to the passenger compartment. Over the years the rubber will separa...

For the ultimate in reliability, converting to a steel hub (stock is cast iron) and adding another wheel bearing is the answer. The double bearing adds better support for wide tires and adds to the support of the axle, greatly decreasing the chance o...

Performance geometry kit includes tie bars, lower arms plus performance bushes for lower arms and tie rods. This is basicaly the same kit as MSSK3013 but less the rear tracking and camber brackets.

parts in kit to transform hand...

Adjustable tie-rod kit with C-STR627 rubber bushes and all bolts,nuts and washers required. This is one car set.

When you change the length of the lower control arm to attain the desired degree of camber, the caster also change...

Conversion mount kit, with fittings to allow the fitment of a manual engine to an automatic front subframe.



Will require to elongate the 2 upper holes on subframe equally, once subframe holes line up with the spacer plate in this k...

This kit contains all the parts from MS44 plus the 4 cast trunnions that hold the rubber bushes. This complete rear subframe fitting kit is what the factory fitted to minis up to 1976 on but the later kit MS41 will fit early...

Mini steering racking fitting kit comprising of 2 U-bolts, 4 nyloc nuts, 2 plastic anti friction stipes, the foam rack to body seal and the half nuts to lock the track rod ends

All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.

All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.

This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.

People also bought products

Boot hinge gaskets and fittings for original type hinges

This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.

Engine mount bolt kit for manual cars, 1 kit requried per car.

5/16" UNF cage nut as fitted to CZH3241 tank bracket on cars fitted with a 7.5 Gallon fuel tank. Uses 13H7583 bolt

Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.

5/16" UNF A2 Stainless Steel Plain nut, ideal for engine bay dress ups or nuts that you don't want going rusty!

A2 Stainless Steel 5/16" UNF Nyloc nut, ideal for engine bay dress ups or nuts that you don't want going rusty!

M6 metric lock nut -fits 14A6779ms bumper

Metric M6 PLAIN NUT.sold singly per item

Required for non genuine stainless steel and chrome bumpers.

Fits radiators with metric fittings such as ARP1110

METRIC FLANGED NUT AS USED ON ENGINE ANCILLARIES FROM 1990 ON

Metric flanged metric M6 nut as used on engine, air con units and heaters from 1990 on.

METRIC M8 nut for holding bolt on spotlamp brackets on SPI/MPI plus other parts

Plain half thickness half inch nut as used on our C-AJJ3365 arms and steering rack adjustment nut for track rod ends.

Wing nut to secure the air filter box on Cooper & Cooper 'S' models.

New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...

Original metric fixing nut for genuine Rover sportspack arches.

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.