BOLT 1/4"x3/4"UNC LONG FOR C-AJJ4006
GHF160

£0.13 exc vat

£0.16 inc vat

In stockIn stock
Bolt used in our anti roll bar kit and for holding plate on speedo drive housing on gearbox

£0.13 exc vat

£0.16 inc vat

In stockIn stock

Recommended usage 2 x GHF160 to fit one mini.
Rod Change Gear Selectors and Speedo Drive - Qty 1
Gearbox Transmission Case 2 - Qty 2
Gearbox Selector Forks - Qty 1

Kit products

This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the...

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the abutment bracket on the inlet m...

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers and stainless steel heatshields plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the...

People also bought products

Engine mount bolt kit for manual cars, 1 kit requried per car.

5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap

Stainless steel version of GFK5184, worth keeping a few spare as they are one of the most common bolts fitted to the Mini.

Bolt for the top alternator bracket on mpi cars.

Stainless steel version of GFK5185, worth keeping a few spare as they are one of the most common bolts fitted to the Mini.

FIA spec anchor plate for eye bolts, used when fitting harnesses. Sold individually, 7/16 UNF 65x65x3mm.

m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)

original imperial radiator screws were SH604031 or PK type were ARA1117

Clutch housing bolt to engine long 5/16" UNC 1.75" long Fitted ffrom 1985 for clutch housing instead of 22A152 stud

Special thread cutting screw 1/4 UNF 1.25" (31mm) long.

Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Self tap screw No10 for holding wiper motor strap to body and any other use.

M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)

Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.

Also the bolt to hold the starter motor.

Also the bolt for the [...

There are 3 of these bolts fitted -1.75"long 5/16"UNF bolt ALTERNATIVE DAM7758.

Also used as longer bolt for water pump.

Also for the 21A1091 heavy duty tie rods on front suspension.

Bolt for CHM85 differential side cover. 1" long UNC useful for pre verto slave cylinder and starter bolt. Also 12A361 engine mounting bracket to alloy case.

Front subframe to front teardrop mounting, clutch case to block.

Engine mounting to subframe - easier to use than the GFK5184 - 3/4" long