FLOAT REP KIT for HIF CARBS
WZX1509A

£43.25 exc vat

£51.90 inc vat

In stockIn stock
This float is ethanol tolerant and will fit all HIF38/44 carbs and the spindle is CUD2082 ..Quantity required-1 set for single carb.

Turbo uses WZX1095 needle valve. An expensive puncture proof stay up float is available to order as AUE895.

£43.25 exc vat

£51.90 inc vat

In stockIn stock

Recommended usage 1 x WZX1509A to fit one mini.
HIF38 Carburettor 38mm 1.5 inch - Qty 1
HIF44 Carburettor 44mm 1.75 inch - Qty 1
Carburettor HIF38 and HIF44 - Qty 1

People also bought products

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

Return spring kit for HS4 carburettor spindle.

Also denoted by its black plastic base. Twin HS4 carbs have 30 degree float bowl angles and therefore this jet is easier to fit as it is longer. L/H carb uses AUD9098A std single HS2 jet.



For...

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

Throttle disc only for HIF44-non turbo and if replacing the spindle there are 2 type, threaded one end only use WZX1127 for very early carbs 1980-81 only, but all later cars were threaded both ends use WZX1128

For HIF38 carbs,this is the full rebuild kit with the spindle and throttle disc and bushes--- see CSK94 for service kit

complete rebuild kit for Turbo type HIF44 carbs including needle valve and throttle spindle plus disc.With damper clamp ring as fitted to turbo only

complete overhaul kit for non turbo HIF44 carb includes needle valve and throttle shaft plus spindle--See CSK75 for service kit less spindle and disc

For 21A2331 pipe. Before the days of Aeroquip, Minis had braided petrol pipes. They should be used in place of rubber for all fuel lines where possible. This is 5/16" bore size for the joining pipe on twin tanks using the original pipe ...

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

THIS CARB IS A GREAT TUNING AID ON TUNED ENGINES, ESPECIALLY 1380cc.

Fuel or water T piece adaptor

used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

Carb repair kit less spindle and butterfly for single HS4 carbs-includes float needle valve and jet. Full repair kit with spindle etc is CRK227-----for waxstat type see CRK121, This kit is suitable for pre Waxstat (pre 74) Minis only

this is the plain butterfly disc for the HS4 1.5" carb and if you have the air valve type butterfly disc see WZX1325

Jet bearing kit for HS4 carb for swinging needle type. This includes the adjusting nut, spring etc.

jet for HIF38 carb and is 0.090 size--for HIF44 see WZX1453A